Täällä vois jatkaa keskustelua Xvostickin klooneista; Fasttech, 3FVape ym.
Printable View
Täällä vois jatkaa keskustelua Xvostickin klooneista; Fasttech, 3FVape ym.
Itsellä kokemusta 3fvapen kloonista. Yllättävän hyvä, täytyy sanoa. Napit toimii hyvin, 510:ssä kierteet hyvät samoin akunkorkissa. Poiketen originaalista tässä on jousitettu plussanasta. Pinnoite (maalattu?) Vaikuttaa ihan ookoolta ja on ainakin tässä yksilössä lähes virheetön, pari olemattoman pientä pistettä josta pinnoite puuttuu. Näyttö (pohjassa) on originaalista poiketen kiinnitetty siten ettei se jousta sisäänpäin ollenkaan, laitettu kuumaliimalla kiinni.
Wattipuoli toimii tässä hyvin, samoin lämmönsäätö joka piirissä hoituu fahrenheitteja säätelemällä. Nikkelicoileja testailtu 0,07 seutuvilla ja hyvin pelittää. Kaikin puolin toimiva kampe tohon hintaan.
Pari kuvaa pohja avattuna. Oli hieman löyhällä tuo akun plussanasta, kiristämällä ok.
Sen verran testailin tuossa vielä että näyttää lukevan noi nikkelicoilien ohmit samoihin kuin originaali.
Pari tuntia nyt hypistelty kloonia :)
Yllättävän pieni ja kevyt tämä on, työmodiksi lähinnä aattelin ja siihen tämä taitaa sopia hyvin. Tuo Fulgoris on vähän liian painava töissä kannettavaksi :)
Hieman nihkeästi Nautilus mahtui tuohon koloon, itseasiassa yksi Nautilus kuudesta ei mahtunut.. 0.05mm isompi halkaisija kuin muissa ??? Ilmeisesti kiinasta ostettu base tuossa yhdessä ???
Hieman on hakusessa tuo käyttö kun mitään ohjelippusta ei ollut mukana....
Herjaa new coil aina kun tankin irrottaa ja laittaa takaisin, saako tuota kyselyä jostain pois ??
Jatketaan testausta ja ootellaan kiinasta toista saapuvaksi ;)
Mulla kyselee tuota coilia melkein kokoajan, ilman että akkua tai atoa irrottaa.
Muuten ihan hyvä :angel:
Mikäs subohm tankki tohon nokalle jonka voisi täyttää yläkautta ja olisi RBA saatavilla? Nyt on kiinni Delta 2 ja saa olla kokoajan ruuvaamassa irti täyttöä varten. Lisäksi tuo Delta kusee noista ilmareijistä...
Bellusta katttelin, mutta siinäkin pitäisi ilmaröörit sulkea täytön ajaksi, eli tankki irti taas...
Osta multa mister 510 ;)
Mitäs tää nyt sit on ?? Aamulla ei tullut oikein kunnolla höyryä, katoin et akkua vielä yksi palkki jäljellä eikä herjannut mitään "low battery" tms. Vaihdoin kuitenkin täyden akun ja johan alkoi höyryämään... Eikä tämä ilmoittele mitään akun hiipumisesta, vaan lakkaa höyryämästä ihan noin vain ???
Akun kun laitoin laturiin, niin näytti 3.42v... Mun muut modit alkaa yleensä herjaamaan tuossa vaiheessa ????
Huvikseenpa testailin niin sxj piiri antoi akun mennä n.3.31 ennen kuin alkoi vilkuttamaan akun loppumista. Sitä ennen antaa kyllä tulittaa hyvän aikaa mutta vetää viivaa tuohon akun päälle ja höyryntuotto vähenee. Sama akku xvostick kloonissa antoi mennä 3.34 ennen kuin hälytti low voltagea.
Laitetaas tähän revikkaa myös kloonista. Mitähän lie revikoijan analogisessa..:D
https://m.youtube.com/watch?v=87UehImcl24
Vaihdoin FT:n Xvostick klooniin aidon DNA40d piirin. Meni niin sanotusti heittämällä. Kiinan pojat tehneet 1:1 kloonin ainakin mittojen perusteella. Ei tarvinnut kuin kolvia ja tinaa tässä hommassa.
Alkuperäinen Klooni piiri toimi muuten ihan ok, mutta noin sekuntin tulitus viive ärsytti. Suoraan keuhkoihin vedettäessä sen kanssa olisi pystynyt jotenkin elämään mutta MTL touhussa ei.
Tilasin bargain vaporilta gold mallin. En ollu ihan varma sen isonäyttöisen sopivuudesta. Piiri oli vähän alle 50€ ja halvimmat postit reilun 5€ luokkaa.
Kuvia ei tullut valitettavasti otettua. Koitan tähän elle kirjoittaa työjärjestyksen niin hyvin kuin muistan. Homma on tosiaan simppeli jos on ennenkin pitänyt kolvia kädessä. Pitäisin tuota kolvausta ehkä vaikeimpana asiana tässä:)
- pohjan 3 ristipää ruuvia auki jotta pohjalevyn saa pois.
- näyttö irti pohjalevystä, kiinni tipalla kuumaliimaa
- akun + johdon irroitus pohjasta avaamalla messinkinen talttapää ruuvi
- irroita ristipää ruuvit pohjasta, toisen alla piirin miinus johto
- irroita 2 kpl kiiltäviä ristipää ruuveja pohjasta joilla rungon ylä- ja alaosa on kiinni toisissaan
- irroita pohjasta pieni kuusiokolo ruuvi joka pitää näppäimistö modulin kiinni.
- kiepauta näppäimistö moduuli sen verran irti että saat usb latauspiirin irti, kiinni kahdella tosi pienellä ristipää ruuvilla.
- irroita 510 liittimeen tuleva + johto pohjasta. Liitin tyyliä FatDaddy. Eli kiertää vaan pihdeillä kiiltävää sileäreunaista pyörylää auki. Nyt saat rungon ylä osan kokonaan irti
- työnnä piiriä yläpuolelta, tulee kelkkana pohjasta ulos. Jossakin vaiheessa piirin irroitusta tulee usb piiri työntää kans pois.
- jätin näppäimistö modulin paikoilleen koteloon, otin kuvan mikä johto menee mihinkin piirillä. Menevät aidolle DNA piirille joka tapauksessa samaan järjestykseen. Katkaisin johdot sivuleikkureilla niin läheltä piiriä kuin mahdollista. Sama homma usb piirin johdoille.
- nyt on piiri irti, kolvia apuna käyttäen loput johdot irti klooni piiristä ja sitä mukaa juottaa ne aitoon piiriin takaisin. Pitää olla tarkka että kukin johto tulee laittaa tismalleen samaan paikkaan ja samalle puolelle uutta piiriä kuin miten ne kloonissa oli. Muuten voi tulla ongelmaa kasaus vaiheessa. Aidosta DNA piiristä nipsasin piirin oman tulitusnapin sivuleikkureilla pois. En ole ihan varma oliko se tarpeen, mutta jäänyt vaan tavaksi.
- näppäimistö modulin johdot juotin kiinni kun olin piiriä jo laittamassa takaisin
- usb piirin pujotus omalle paikalleen ja ruuvien kiinnitys
- kasaus muuten käännetyssä järjestyksessä.
- ihan lopuksi näytön liimaus pohjalevyyn mieluiten kuumaliima tipalla niin tarvittaessa saa joskus poiskin.
Tästä taisi tulla vähän pitkä eeppos, kuvat olisi olleet kyllä käteviä. Seuraava tuunaaja voisi kuvat napsaista ja korjata ohjetta tarpeen mukaan. Homma on kyllä paljon simppelimpi kuin ohje antaa ymmärtää:)
Täällä myös otettu ensi kokeilut Fasttechin kloonin kanssa. Toistaiseksi ei huonoa sanottavaa.
Tuntuu loistavalta peliltä. Subitankki kanthalilla ja Crius nikkelillä toistaiseksi ollut nokalla.
Muutama juttu jota jouduin hakemaan asetusten osalta:
- Tehon lukitus: Näyttö päällä -> ylös+alas napit pohjaan / lukko pois -> napit pohjaan uudestaan
- Lämmön maksimirajan asetus -> lukitustilassa (5 krt tulitus) -> ylös+alas napit pohjaan. Haarukka 200-600F. Rajoitus pois päältä kun rullaa yli 600F
Lukitustilassa näytön säätö
- Paina tulitusnappia ja perään alas nappi pohjaan -> asetus rullaa normitilan ja stealth-tilan (näyttö pois päältä) välillä
- Paina tulitusnappia ja perään ylös nappi pohjaan -> näytön asennon säätö, rullaa left ja right tilojen välillä
Ja tänne sama, pätenee klooninkin purkuun, eri ruuvinkannat tosin.
https://youtu.be/Nf5MhzKEhlc
Mulla on tuo FT:n "kalliimpi" klooni.. Muuten pelaa hyvin, mut kyselee monta kertaa päivässä tuota new coil/old coil hässäkkää... En tiedä miksi, enkä edes käytä lämpösäätöä ??
Mulla on toinen klooni forkalta ostettu ja tää ei kysele muuten kuin akun vaihdon tai tankin irrotuksen jälkeen.
Toi Crius tosiaan toimii hirveän hyvin tässä. Tankin yläosa jää millilleen modin yläpinnan tasalle eli siitä kiertämällä nestevirtaus kiinni ja vetämällä nesteet sisään. Näyttääkin tosi hyvältä kimpassa. Mullahan tuli ensin viallinen yksilö jonka lähetin FT:lle takaisin. Tarvitsi kuvata video mistä kävi ilmi ettei täydellä akulla lähtenyt edes käyntiin. Yrittivät ensin sitä että olisin korjauttanut täällä ja olisivat hyvittäneet ostoksissa 8 taalaa :thinking:No, pistin paketin postiin ja hyvittivät postikulut. Hieman hirvitti, kun vaativat halvinta mahdollista tapaa mutta toisaalta piti olla siellä kahdessa viikossa. Tänään se kuitenkin tuli postiin, eli loppu hyvin jne. Ja olihan tässä sekin onni että näyttö on paljon parempi; aikaisemmassa oli ohut muovi joka liikkui mutta tää uusi on jämäkkä. Snadisti vaatii käyttö totuttelua kun peukulla on tottunut tulittamaan. Tätä käytän nimettömän keskiosalla. Ihan kiva vempula.
Tuossa sun rikkonaisessa modissa oli sitten se näytönsuojana oleva pleksilevykin irronnut liimauksestaan, se on kuumaliimatipalla näissä klooneissa kiinni, vaihtelevalla menestyksellä. Olen tuollaisia liimannut kiinni kun ovat irtoilleet.
Mulla on toisessa kloonissa tuo 510-liitin niin tiukassa, ettei sitä käännettyä haluttuun asentoon.. En tiedä onko se liimattu kiinni vai mikä mättää. Onko muilla tällaista ongelmaa esiintynyt ???
Mulla sama homma, aika tosissaan oon koittanu sitä vääntää mutta ei se liiku :D
Saattaapi olla että näissä on sitten kiinteä tuo decki.
Omassa FT:n kloonissa kyllä dekin saa pyöriteltyä irti kunhan tosiaan sen lukitusruuvin ensin irrottaa.
Eikä ole leakproof tämä dekki, kannattaa välillä kurkata paljonko on laskenut alleen.
Kloonissa kyllä, dekin alla on reikäreunus johon lukitustappi lukittuu, sieltä sai kuivalla litkuja.
Dekki pyörii parhaiten kun tunkee lukitustapin reikään vaikka meisselin (hih) ja pyörittää sillä.
Kasatessa sitten keskipinnin taiteilu kohdalleen on oma hauskuutensa, ehkä kannattais jopa avata alhaalta sitä varten.
Muuten ihan ok klooni mutta leakproof ei tosiaankaan ole.
Ok. Ei tuohon klooniin varmasti ole luvattukaan 510-liittimen leakprooffia, ja se käsittääkseni meinaa että neste ei pääse tuonne modin sisään asti, plussan kautta. Klooneissa jousitettu plussa mitä ei aidossa mallissa ole, sen takia kun olivat halunneet pitää ne nesteet modin ulkopuolella ja tuosta tuo leakproof.
mulla on fastechin aito klooni ( :thumbsup: ) jossa on härskisti paketissakin mini-ecigin mainokset. Toiminut muuten hyvin mutta tässä on bugi että satunnaisesti tulittaa säädettyä isommalla teholla. Ei ole kuitenkaan ollut iso ongelma koska esiintyy ehkä kerran per 5 tankillista ja modissa on kuitenkin maltilliset tehot niin ei kärähdä atopää heti.
Otin piruuttani kloonista pohjan auki.. Tuo musta johto ei varmaankaan kuulu olla litistyneenä ilman kuorta tuossa kannen alla ???
Eka sivulla olikin Morgan Kanen kuva, siinä ei ollut musta johto litussa kannen alla :)
Toimii edelleen. En saanut 510-liitintä vieläkään pyörimään. Pitää väsätä joku työkalu (tappiavain) et saa alakautta väännettyä..
Liite 26651
Oisko luova tapa yrittää maadoittaa runko, vaikka anodisoitu pinta taitaa johtaa aika heikosti?
Noin mullakin tuo toinen klooni toimii, mut tää toinen on ilmeisesti alakautta jollain työkalulla väännetty niin tiukkaan kiinni, ettei normikonsteilla liiku.. Ei sillä muuten väliä, mut sais ilmareiän sopivalle kohdalle, ettei vihellä... Pitänee kokeilla toisella tankilla ja sattuis reikä paremmin kohdilleen..