Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
rossian
Ei nyt varsinaisesti liity asiaan, mutta liippaa läheltä.
Vaihdatteko setupin kun vaihdatte nestettä, setupin käyttöikähän on huomattavasti pidempi kun 10ml nestepullon..
Eli siis jääkö nesteiden maku kuinka hyvin tuohon meshiin, jos vaihtaa esim kahvinmausta johonkin sitruunaiseen.
Eipä ole tullut mieleenkään laittaa toimivaa setuppia uusiksi :P nyt taitaa olla jo 10 tankillinen samalla setupilla ja setuppi on laitteen toinen toimiva, jos ei toimi niin silloin vaihdan vaikka kesken tankillisen :)
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
rossian
Ei nyt varsinaisesti liity asiaan, mutta liippaa läheltä.
Vaihdatteko setupin kun vaihdatte nestettä, setupin käyttöikähän on huomattavasti pidempi kun 10ml nestepullon..
Eli siis jääkö nesteiden maku kuinka hyvin tuohon meshiin, jos vaihtaa esim kahvinmausta johonkin sitruunaiseen.
Meikäläinen ei ainakaan vaihda. Yks helvetin voimakkaan makunen (DIY) kahvineste kummitteli muutamat imut Somniumis ku vaihdoin päärynään, mutta se asettu sitte. (: Jos on hyvin toimiva setuppi, niin ei sitä passaa ronklata, sen verran tuntuis olevan henkimaailman hommia.. :D Ainaki meille joilla on vähemmän kokemusta. :p
Vs: Meshin käärintää ja vastuslangan virittelyä
mikähän mahtaa olla nyt vikana kun yritän tehdä tuohon Puff DID style griffin atoon niin aina kanthali palaa poikki aivan sieltä yläkierukasta..ja ohmiksi olen saannut vain noin 1.5 ohm..olisi hyvä jos saisi edes tuonne 2-2.5 ohm paikkeille.
kanthali on tätä: Kanthal A-1 0,20mm 43,48ohm/m
olisi mukavaa saada vihdoinkin ne ekat höyryt tuosta pihalle kun laite tuli jo noin viikko sitten =)
Re: Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja djtimse
mikähän mahtaa olla nyt vikana kun yritän tehdä tuohon Puff DID style griffin atoon niin aina kanthali palaa poikki aivan sieltä yläkierukasta..ja ohmiksi olen saannut vain noin 1.5 ohm..olisi hyvä jos saisi edes tuonne 2-2.5 ohm paikkeille.
kanthali on tätä: Kanthal A-1 0,20mm 43,48ohm/m
olisi mukavaa saada vihdoinkin ne ekat höyryt tuosta pihalle kun laite tuli jo noin viikko sitten =)
Ottaa meshiin maihin?
Edit. Koita ottaa wicki pois, tohottaa ja nestepolttaa kunnolla uudestaan. Saattaa auttaa. :p Tai sitte hellästi siirtelet sitä ylintä kieppiä jollakin ja yrität saada hehkumaan tasasesti. (:
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
djtimse
mikähän mahtaa olla nyt vikana kun yritän tehdä tuohon Puff DID style griffin atoon niin aina kanthali palaa poikki aivan sieltä yläkierukasta..ja ohmiksi olen saannut vain noin 1.5 ohm..olisi hyvä jos saisi edes tuonne 2-2.5 ohm paikkeille.
kanthali on tätä: Kanthal A-1 0,20mm 43,48ohm/m
olisi mukavaa saada vihdoinkin ne ekat höyryt tuosta pihalle kun laite tuli jo noin viikko sitten =)
Lyö oikkariin. Toi yläkieppi on yleisin paikka mihin tulee hotspot. Helpottaa kun löysää sitä hieman, joko pyörittämällä keskinapaa(joissain, kuten somnium, se on pyörivä) tai sitten vaan asettelemalla uudelleen.
Liian tiukkaan kiertämällä rikkoo helposti hapetetun pinnan meshistä ja sehän lyö iloisesti oikkariin ;)
Re: Meshin käärintää ja vastuslangan virittelyä
No mitä oot tehny ja mitä jättäny tekemättä? Tolla kysymyksellä pitäis taas kaikki neuvoa alusta asti. Oikosulkuun se menee ku polttaa kanthalin poikki.
Tohota meshiä lisää ja poista mahdolliset hot spotit aluksi pienemmillä volteilla. Jollei auta niin kato pari opetusvideota ja yritä aluttaa taas alusta. Tsemppiä. :)
Re: Meshin käärintää ja vastuslangan virittelyä
Perkeles, kerenny kännykällä editoida vastausta paremmaksi ku muutki alkaa jakaa apua. :D Ollaan me höyrypäät vaan huippuja. :D
Vs: Meshin käärintää ja vastuslangan virittelyä
ok..no veikkaan, että vika siinä ettei ole hapetettu tarpeeksi meshiä..kaikki olen ohjeen mukaan tehnyt ja moneen kertaan kanthalin poikki polttanut..voisiko joku vielä sanoa että miten tuo hot spotit poistetaan :esmoke: pitää huomenna jatkaa kun tulee uusi putki tuohon tankkiin.
Re: Meshin käärintää ja vastuslangan virittelyä
Hellästi ja varovasti vaikka hammastikulla siirtelet sitä kieppiä jossa on hotspotti. Matalilla volteilla testailet että katoaako. Jos koko vastus hehkuu tasasesti, on siinä voittaja. :D
Edit. Älä siis kuitenkaan samalla räplää coilia ku tulitat, katkee herkästi.
Vs: Re: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Barole
Hellästi ja varovasti vaikka hammastikulla siirtelet sitä kieppiä jossa on hotspotti. Matalilla volteilla testailet että katoaako. Jos koko vastus hehkuu tasasesti, on siinä voittaja. :D
no perhana..hemmetin yksinkertaisen kuuloista ainakin näin foorumin välitykssellä, mutta saa nähdä lähteekö huomenna loputkin hiukset päästä kun koitan saada taas tuota toimimaan..no onneks tuli 4metriä kanthalia tänään niin eiköhän niillä yksi toimiva setti saada aikaseksi :esmoke:
Vs: Meshin käärintää ja vastuslangan virittelyä
Täältä varmaan saisin jonkin laisen vastauksen... Eli milläinen meshi härveli kannattaisi ostaa ekaksi mesh härveliksi?? Onko mitään väliä minkä ostaa? Hintaa voisin pistää noin 30-50€
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
djtimse
ok..no veikkaan, että vika siinä ettei ole hapetettu tarpeeksi meshiä..kaikki olen ohjeen mukaan tehnyt ja moneen kertaan kanthalin poikki polttanut..voisiko joku vielä sanoa että miten tuo hot spotit poistetaan :esmoke: pitää huomenna jatkaa kun tulee uusi putki tuohon tankkiin.
Sähkö kulkee sitä reittiä, jota se helpoiten pääsee. Tee kaikkesi jotta sähkö ei kulkisi meshin kautta runkoon, vaan kanthalia pitkin runkoon. -.-
-mesh ei saa ottaa pohjaan kiinni
-mesh ei saa olla liian tiukka reikäänsä (hapettunut pinta voi rikkoontua)
-coil ei saa olla liian tiukalle kääritty (hapettunut pinta voi rikkoontua)
-liika teho voi polttaa langan vaikka kaikki muu olisikin kunnossa
-huono kanthal voi vaikeuttaa (kai sulla on A-kanthalia?)
Eipä sitä sen paremmin voi kertoa. Kokeilemalla oppii. ;)
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
hesekiel
Sähkö kulkee sitä reittiä, jota se helpoiten pääsee. Tee kaikkesi jotta sähkö ei kulkisi meshin kautta runkoon, vaan kanthalia pitkin runkoon. -.-
-mesh ei saa ottaa pohjaan kiinni
-mesh ei saa olla liian tiukka reikäänsä (hapettunut pinta voi rikkoontua)
-coil ei saa olla liian tiukalle kääritty (hapettunut pinta voi rikkoontua)
-liika teho voi polttaa langan vaikka kaikki muu olisikin kunnossa
-huono kanthal voi vaikeuttaa (kai sulla on A-kanthalia?)
Eipä sitä sen paremmin voi kertoa. Kokeilemalla oppii. ;)
no eiköhän tuon huomenna saa pelaamaan :D
Kanthal A-1 0,20mm 43,48ohm/m
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
pdz4
Täältä varmaan saisin jonkin laisen vastauksen... Eli milläinen meshi härveli kannattaisi ostaa ekaksi mesh härveliksi?? Onko mitään väliä minkä ostaa? Hintaa voisin pistää noin 30-50€
Jos kehtaat lisätä budjettiin kympin tai pari niin DID.
Muuten joutuu tyytyyn johonkin enemmän ja vähemmän loistavaan, Picoon, "Mersuun" tai tohon Did griffin tankiin. Omista taidoistahan toimivuus on kiinni, mutta rahalla saa laatua ;)
Vs: Re: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Barole
Hellästi ja varovasti vaikka hammastikulla siirtelet sitä kieppiä jossa on hotspotti. Matalilla volteilla testailet että katoaako. Jos koko vastus hehkuu tasasesti, on siinä voittaja. :D
Edit. Älä siis kuitenkaan samalla räplää coilia ku tulitat, katkee herkästi.
Kyllä sitä voi räplätä aivan huoletta tulittaessa...
Vs: Meshin käärintää ja vastuslangan virittelyä
mistäs tuo kannattaisi sitten ostaa?? Joo ja ei se muutamasta kylmpistä ole kiinni johan tähän hommaan on muutamat kympit uponnut :D
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
pdz4
mistäs tuo kannattaisi sitten ostaa?? Joo ja ei se muutamasta kylmpistä ole kiinni johan tähän hommaan on muutamat kympit uponnut :D
http://www.e-savuke.com/forum/index.php?topic=5057.0 - Tuosta 70e ja viikonlopuks leikkimään. :-)
Vs: Re: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
teekkis
Kyllä sitä voi räplätä aivan huoletta tulittaessa...
Kyllä mä oon tähän päivään asti eläny siinä uskos että jos kanttaali hehkuu punaasena niin son silloon sen verran pehemiää että napsahtaa herkkään poikki.. :o
Vs: Re: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Barole
Kyllä mä oon tähän päivään asti eläny siinä uskos että jos kanttaali hehkuu punaasena niin son silloon sen verran pehemiää että napsahtaa herkkään poikki.. :o
No ei mulla ainakaan ensimmäinenkään oo ton takii poikki menny. Ja tässä myös master-Zenin ohje;
http://www.youtube.com/watch?v=ZxGfAmIcs70
Re: Meshin käärintää ja vastuslangan virittelyä
Mystistä.. No, mitenkä vaan. :D