Mulle 1 kpl, kiitos!
Printable View
Meni jo kaikki :/
höhlä, oisin ottanut. Onko muuten tietoa onko v2 ja v3 hatut samanlaiset ? eli sopiikohan tuo sama kuristus myös vanhempaan.
eiköhän noita lisää tule kun saan itsell i-attynniin voin sitten tehdä lisää
laitoin ilen poojat teile 1.lk kirjeet joten laittakaas kokemuksia niistä kuristuksista sitten. meshin palalla sitten junttaan sen hattuun kiinni jos on väljä :)
Kuristuspala saapui tänne ja on niin lähellä kyllä plussa tolppaa, että ei ainakaan suoriltaa pysty käyttää ainakaan matka käytössä.
Pikaisella testauksella antaa kyllä makoisat höyryt tuon avulla.
Pitää vähän viilailla tuota avarammaks niin uskaltaa pitää sitä jatkuvasti siellä.
Kokemusta on meinaa kun RSST:ssä oma kuristus pala ja oli alkuun todella lähellä kans plussa tolppaa. Kännissä sitten tuli otettua höyryt ja hattu oli pikkasen kalleellaan ja tietenki oli kuristuspala kiinni plussassa ja EAmod kloonin nappi kuumeni aika äkkiä ja sen pohjajousi meni kasaan eikä tulittanu ollenkaan. =)
Eli siis käyttäjävirhe yhtäkaikki? :D
Hyvin pelaa kuristukset, makua tulee sopivasti enemmän :esmoke:
:/ ei se kyllä tolppaan kiinni ota kun kaikki testasin ja mesh palalla hattuun kiinni niin se sieltä mihinkään liiku
Juu ei se otakkaan, mutta on todella lähellä, joten pienikin hatun liikahdus, niin nappaa kiinni.
Mutta hyvin tuo tosiaan pöhisee parhaillaan ja Jugo diablo maistuu jälleen paremmalta =)
Kiitoksia terokum tuosta palasta.
Olkaa hyvä nöyräksi vetää...
Mulla teki saman ku Rsst.ssä toi kuristus. Aluksi toimii vähän aikaa mahtavasti mutta kun ketjuvapoilee niin maku muuttuu huonoksi. Tulee jotain ylimääräistä tosi tunkkasta makua mukaan.
Pitänee laittaa kunnon pesuun noi kuristukset ja testailla uudestaan.
Hyvin ainakin hattuun istuu terokumin pala. Maku muutoksista ei oikeen osaa mitään jälkiflunssassa sanoa, kun ei oikeen mikään maistu miltään tällä hetkellä.
laittakaa ihmeessä uudestaan pesuun ne on käyny 15min ultrapesun mutta kannattaa silti pestä uudelleen jos mahd
Laitetaan nyt tänne vaikka onkin enemmän yleisluontoinen kysymys. Eli sain lainaan tämännäkösen yleismittarin. Pitäskö tolla saada chybbestä jotenkin järkevästi mitattua vastus? Pomppii niin perkuleesti numerot ruudulla, ettei kyllä mitään luotettavaa tulosta saa aikaseks. Yritin siis eri kohdista, mutta oletan, että nimenomaan kanthalin päädyistä pitäs mitata. Ainoo missä sain luvun pysymään paikallaan oli carto ja siinä se vaikutti kutakuinkin oikealta(0.1 enemmän kuin provarilla).
Dropin sain ruuveista kyllä mitattua ja totesin sen olevan jotain 0.7 luokkaa tän hetkisessä setupissa. Ei todellakaan hyvä, mutta ainakin se antaa aina saman verran ulos nappia painaessa, toisin kuin aikasemmin.
E: Jaa, vaatiikin erittäin vakaata kättä. 0.9 ohmissa sain pysymään aikani tähtäiltyä vaikkei aikasemmin onnistunut alkuunkaan. Kaippa tuo on suurinpiirtein mitä voi neljällä 0.30 kierroksella odottaa.
Vähensitkö mittarin oman vastuksen tosta lukemasta? Eli mittarin johdot yhteen ja se luku vähennetään siitä oikeasta mittauksesta.
Mä oon saanu dropeiks 0.3-0.4v 18350/18500 akuilla ja n. 0.8ohm setupilla.
Kattelin, että mittarin johdot yhdessä sanoo 0 - 0.1 eli se vastuksen mittaus jää aika pitkälti riippumaan siitä, että mistä kohtaa kanthalia mittaan ja saako kädet pysymään paikallaan sen muutaman sekunnin.
Droppia on tosiaan toi 0.7v nesteet sisällä tulittaessa, en tiedä onko siinä jotain kontaktihäiriötä ihan mittarin ja ruuvien välissä. Kovasti yritin kumpaakin ruuvia vatkata edestakas ja asetella kanthalia paremmin, mutta ei vaikutusta. Ilman setuppia ruuveista mitattuna ei ole dropista tietoakaan. Nyt parin päivän tauko laitteesta, ettei suotta suutahda ja ens kerralla vois varmaan koittaa hioa kevyesti sekä putsata noi kanthalin kosketuskohdat.
Niin se vaan on että misteri tuli käymään, mutta chybridit vei voiton siitäki.
Lähtee misteri jatkamaan matkaa muualle :yawn:
Jonkun tekemä pieni video chybridistä. Kuka tunnustaa?
testissä i-chybrid V3 Puffilta - YouTube