-
Juu kyllä mun mielestä on ihan pätevä peli. Setupointi on mun makuun sopiva ainakin. Ihan vaivatta eksy vaijeri paikalleen ja tuntuu sähkö kulkevan varsin kovaa yläkertaan.
Jokaisen setupit on tietty aina oma juttunsa ja monen asian summa, mutta mulla tuli tasan laakista toimiva paketti.
Sellanen tuli mieleen, että tossa plussapostin sormiruuvissakin vois olla lovi ruuvarille.
Video tulee, kun saan sopivasti aikaa. PE-LA siis
-
Havaitsin pientä vuotoa 510-liittimeen, tuntui välillä höyrytkin melko köykäsiltä (2mm vaijeri / 3 kieppiä 0.32 lankaa). Noh, purin aton ja totesin että keskiposti oli aivan musta karstoittuneesta kondensiosta tai mistä lie. Operaatio puhdistus Maguairsilla kaikki osat läpi... vuodon luultavasti aiheutti väljähkö plussapostin yläeriste. Laitoin sen tilalle toisenlaisen toisen aton varaosapussista (olisko Steamboy tai H-atty) ja sehän istui kivasti. Alkuperäisen pikku o-renkaan jätin alle. Ato kiinni top capiin ja plussapostin kiristys niin huolto oli valmis. Samalla coilin kiinnitys nousi vähän korkeammalle ja mielestä ilmareiät kohdistuu nyt tosi hyvin.
Sitten perinteinen setuppi 200 meshistä ja tupla 0.20 langasta kolmet kiepit -> aivan jäätävä ero aiempaan höyryissä. Ei meinannu malttaa modia kädestä laskea :o Tietty huollon myötä virrankulku on sitä mitä hopeoiduilta kontakteilta voi odottaakin, ja ehkä toi ilmareikien parempi kohdituskin pikkusen vaikuttaa. Jospa nyt pysyy plussaposti paremmassa kuosissa ja dekki tiiviinä kun tuon eristeen vaihtoi.
-
Mulla oli myös tippa tuolla 510-liititmellä kun äsken vaihdoin nestettä.
Pitänee siis tutkia vähän sen tilannetta kanssa.
Sama setup, kuin alkujaan kiinni; 2mm vaijeri ja 400 mesh. 3 kieppiä 0.32 narua ja 0.6 ohm huutelee.
100% VG Boba's Bounty nousee itsekseen yläkertaan :blink::yeah:
En ois ihan heti uskonut, mutta kyllä se perkele sen nesteen jaksaa nostella.
Nyt vaan toi cappi kuumenee niin saatanasti tone setupin kanssa, ettei kehtaa taskuun laittaa, tai on poltettu kohta reidessä :D
-
Toi vuoto loppuu kun kiristää pluspostin alempaa mutteria eristettä vasten. Sielä eristeen alla on pikkuinen tiiviste rengas ja se on luultavasti löysällä. Täs mun atos ainakin auttoi kun huomasin saman vuoto ongelman.
Hyvä ato kaikin puolin muuten mutta 510 liittimen kierteet on kyllä aika kuraa. Saapa nähdä kauanko noi kierteet kestää ennenku korkkaa:confused:
-
Ostohousut on jalassa, mutta ainoa mikä mietityttää on tuo ilmareikien sijoittelu suhteessa coiliin. Lisää revikkaa ja mielipiteitä kiitos! RSST:ssä en ole kokenut ongelmaksi kondession kertymistä ilmarööreihin (stäkätyt siinäkin). Kondenssiota on kertynyt RSST:ssä, mutta sen voi puhaltaa takaisin kammioon tai ihan vain kuivata kammion paperilla.
Mahtaakohan Esmoke valmistaa vaihtoehtoisia kammioita, eri ilmarei'ille ja eri korkeuksille?
-
ihan toimiva mun mielestä toi sijoittelu noiden ilmareikien suhteen. En ole mitään erikoista tai sen kummemmin negatiivista noista löytänyt. Maku hyvä, höyry hyvä ja iskee ihan justiinsa niinkuin pitää.
Mullakin loppui viimein vuoto 510-liittimestä, kun otin ronskimman kiristyksen sille alemmalle ruuville.
Mun mielestä toi kahden snadin rei'än setti on ihan hyvä, koska JOS haluaa että imu vähän löysenee, voi tot toista reikää varovasti suurentaa, tuhoamatto koko systeemiä ihan totaalisesti.
Mun makuun toimii kuitenkin vakiona kuten haluan
-
LSVap lupasi revikkaa tehdä tuossa kunhan ehtii. Noiden ilmareikien osalta ei ole tulossa muutosta koska ovat toimineet sen verran hyvin.
-
Taistelen itseni kansaa, etten tilaisi toista Novumia.. ;)
Vähän tämän ekan sarjan 510-liittimen kierteet 'rouheat' ja jotenkin niitä voisi siloitella, mutta miten?
-
Eikai tuohon ole vaihtoehtona kuin kierrepakka, tietysti karheaa tekokuitua olevalla kiillotusharjallakin voi saada ihan hyvää.
-
Mistä kierrepakka ja millainen? Paljonko maksaa?
Ei tuo ole ensimmäinen jonka kierteitä voisi fixata ja ei myöskään takuulla viimeinen, joten vois jopa hankkia.
-
Pistä tulemaan meille kaupalle niin käydään se kierre läpi. Jos haluat itse niin M7x0.5 tai M7x0,5 hakusanalla ebayhin löytää suhteellisen edukkaita. Noilla halvimmilla ei kierteitä tee, mutta käy kyllä valmiit kierteet ihan nätisti läpi.
-
No en kai nyt parasta atoani ala postittamaan ja Vantaalta en ihan sinne asti viitsi piipahtaa tuollaisen takia.
Laitoin jo ebaysta tilaukseen, eipä näyttäneet montaa euroa maksavan.
-
Wickausongelmia oli pelkällä kokonaan tohotetulla meshillä +15 watilla, mutta nyt tuoreimmalla virityksellä jossa hapetin vain coilin ympäryksen tuntuu wickaavan ihan kiltisti. Metka homma. Kokeillaan vaijerilla vielä kun Puolan pojat saavat perille.
-
Jotku näitä arvosteluita kaivannut, tässä höyryguru defunctan mietteitä atosta:
http://www.youtube.com/watch?v=YUn2HssJRJw
-
Guru oli sitten leikannut videolta vahingossa pois höyryn arvostelun, joka oli siis ensiluokkaisen hyvää :D
-
Voi vittu että repes perse näin kuumeisena kun rullas tuo sun muksu tuohon kuvaan :D
-
Pitääkö munkin ottaa mukelo mukaan omalle, vähä apinoida gurua. :o
-
Pitihän se tämäkin tilata,kun tuntuu tulevan kehuja enemmän kuin kitinää.
Nyt odotetaan että saadaan putki tähän atoon,toiveena on Diablo mods Reaver rst/messinki päädyt
tai swan.
-
Tälläinen projekti käynnissä.
Eli tarkoituksena olisi saada mahdollisimman helppo ja laadukas allday carry -laite, missä ei ole tingitty mistään kohtaa.
Kyseessä on ns. one piece -hybridi, eli ato ja putki on yhtä puuta, joka tietysti lisää tukevuutta, vähentää kontaktien määrää ja tekee modista lyhyemmän.
Proto on 18650 akulle, halkaisija on 22mm ja pituus vain 131mm, toivottavasti tuosta saadaan vielä hieman pois, mutta on tämä silti pakettina pienempi kuin yksikään mun omista 18500 modi + ato compoista.
Kontaktit on hopeoituja kuten novumissa on totuttu.
Aikataulu on jossain vuoden vaihteessa. Viimeisimmät protot on nähtävillä vapefesteillä. Tämän hetkinen on melko raaka proto ja muutoksia voi tulla paljonkin, mutta tältä se nyt näyttää.
http://i.imgur.com/eq0vtZz.jpg
http://i.imgur.com/jHxyINi.jpg
http://i.imgur.com/zr8Js51.jpg
-