Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Charun
Jaa? Oisko pistää faktaa pöytään tälle väitteelle?
Hyvin pöhisee Provarilla, Lavatubella ja VMaxillakin. ;)
Itse en voi sietää pelkkiä akkuputkia, koska akun varauksen laskiessa vähenee myös höyryt, eli itselleni ihan minimi on Kickattu putki.
Makuasioita. :)
Perusteluina on se, että setupin tekeminen on paljon helpompaa mekaanisella putkella kun ei hotspotin sattuessa tarvi erroreita katella. Ite tykkään vääntää about 0.8 ohmin setuppeja, jolloin ei suurin osa (yksikään) vv-putki suostu antamaan mitään virtaa, tai jos antaa niin se on 3.3V luokkaa. Putkimodilla saa sen 4V puskettua alkuun. Kicktulla putkella en kans tee mitään genesis-atojen kanssa, sillä aina on tehot yli 10W. Silica-virityksillä vv ja vw on oikeen toimiva, mutta genesiksillä mielestäni ei.
Vs: Meshin käärintää ja vastuslangan virittelyä
Totta tietysti tuokin, mutta omilla 1.5-2.5:n ohmin käärinnöillä Provari on kyllä passeli laite. Myös tuo Kickin 10W rajotin kiristää välillä, kun tuota KF:ääkin (joka siis on silica-vehjas) tulee ajettua reilulla 12W ja Atomaisteria (=Genesis ato) vielä kovemmilla tehoilla. :P
Silicavehkeissä en ainakaan itse ole kertaakaan onnistunut hotspottia saamaan aikaiseksi, tosin kyllähän se varsinkin tuon Atomaisterin kanssa harjoitellessa helpotti, kun sai hotspotit näkyviin Prodigyllä, mutta eipä ole muutamassa viimesessä setupissa siinäkään hotspotteja ilmennyt, kun pääs hommasta jyvälle. :)
Vs: Meshin käärintää ja vastuslangan virittelyä
Hitto ku oon ihmetelly että mikä mussa on vikana. Että enkö vaan osaa rakentaa Steam Machineen hyvää setuppia. Tänään sitten tajusin että tossa Steam Machinessa on vaan kovempi throathitti kuin bogen cartoissa. Bogella 18mg nesteet on just sopivia, mutta Steam Machinella polttelee samat nesteet kurkkua vähän turhan paljon. Makua löytyy runsaasti ja ei tule palaneen makua suuhun. Ei hot spotteja jne. Se on vaan pakko olla että tosta tulee jotenki kovempi TH kuin bogen kartoista. Oonko oikeilla jäljillä? Jos oon niin pitää testailla 12-15mg nesteillä seuraavaksi.
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
dasazo
Hitto ku oon ihmetelly että mikä mussa on vikana. Että enkö vaan osaa rakentaa Steam Machineen hyvää setuppia. Tänään sitten tajusin että tossa Steam Machinessa on vaan kovempi throathitti kuin bogen cartoissa. Bogella 18mg nesteet on just sopivia, mutta Steam Machinella polttelee samat nesteet kurkkua vähän turhan paljon. Makua löytyy runsaasti ja ei tule palaneen makua suuhun. Ei hot spotteja jne. Se on vaan pakko olla että tosta tulee jotenki kovempi TH kuin bogen kartoista. Oonko oikeilla jäljillä? Jos oon niin pitää testailla 12-15mg nesteillä seuraavaksi.
Periaatteessa joo, periaatteessa ei :)
Troathitin määrä on täysin verrannollinen siihen kuinka lähellä ilma-aukkoa coili on. Dumppaa sitä coilia siinä kupissa syvemmälle niin th pienenee, sen saa todella olemattomaksi Steam Machinessa.
Vs: Re: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
-ih-
Tosta 2:30 paikkeilta kun katsot niin aika löysälle se ylämutteri kiristyy:
Kiitti vinkeistä -ih-. Tein täysin uuden wickin, joka on silmin nähtävin parempi kuin 2 ekaa. Uudella setupilla lähti toimimaan hyvin (ainakin toistaiseksi...). Sitä ennen vahdattiin monta youtube videota ja luettiin tämä ketju läpi :) Tuli tehtyä tohotos kunnolla, lisäksi käytin normi sytkää tohotuksen jälkeen wickiin ja lankaan. Lopuksi vielä rizlaa väliin ja tuloksena ei hotspottia. Tämä toimi hetken hyvin ja sitten iski taas hotspot wickin yläreunaan :( Siirsin hotspotin kohdalta vähän lankaa ja nyt toimii ainakin vielä hyvin. Täytyy sanoa, että kyllä silica atot on vaan helppoja ja ainakaan vielä did ei oo päässyt maussa edelle, mutta johtuu varmaan omasta setupista ja ehkä vaatii vielä sisäänajoa.
Vs: Meshin käärintää ja vastuslangan virittelyä
Kuinka vaikeeta toi setupin virittely on ihmiselle millä on vähän peukalo keskellä kämmentä? Oppiiko nopeeta? Tekis mieli hommata rebuildable ato, mutta juuri tuo seikka "jännittää".
Vs: Meshin käärintää ja vastuslangan virittelyä
Vs: Meshin käärintää ja vastuslangan virittelyä
Sanon suoraan näin mesh ato amatöörin suusta, että osta ensin silica pohjainen korjattava ato esim. penelope, odysseus tai svoemesto kayfun. Mesh pohjaiset atot on varmaan hyviä, mutta vaatii hermoja ja paljon :D Setupin teko penelopeen on lastenleikkiä did:iin verrattuna. Ehkä mä tuon did:in vielä seljätän ja mieli muuttuu täysin mesh atojen kanssa :esmoke:
Vs: Meshin käärintää ja vastuslangan virittelyä
Mulla Didiin onnas 3:s setuppi :) Helekatin hyvä maku ja höyry kohillaan. En jaksanu värkätä sen homman kans ja siirryin silica-vehkeisiin ;)
Rapian kuukauden touhunnu niitten kans eikä yhtään epäonnistunutta setuppia, yx paha vuototapaus mut sekin omaa huolimattomuutta :D
Toiset tykkää emännästä ja toiset tyttärestä 8), näinhän se on aina menny ;)
Vs: Meshin käärintää ja vastuslangan virittelyä
Lataan reilun gigan tiedostoa Youtubeen Meshin teosta DIDiin... siis aasta ööhön ja kaikki noin 15 minuutissa.
Tuo vaatii vielä vähän yhdistelyä ja kikkailua, joten huomenissa on nähtävissä, mutta laitan linkin sitten tänne.
Re: Meshin käärintää ja vastuslangan virittelyä
Näin aloittelijana ja DIDä maanantaista käyttäneenä voin omasta puolestani sanoa että hanki RTA ihmeessä. Itselläni ei ole ollut mitään ongelmia "setupin" teossa kun käyttää hieman maalaisjärkeä ja katselee konkareitten ohjeistus videot läpi uutuubista. Höyryt ja maku paranee :)
Vs: Meshin käärintää ja vastuslangan virittelyä
Eilen tuli päiviteltyä vähän tuota genesis valmistus kalustoa. Ennen olen meshit töhötellyt sellaisella pienellä kaasukolvilla, missä ei kovin iso liekki ollut. Se taisi olla suurin hotspot yms ongelmien aiheuttaja, eli mesh ei hapettunut tarpeeksi (en hapettanut tarpeeksi pitkään).
Kävin biltemasta hakemassa tälläisen (14,99€) ja siihen kaasusäiliöt (myydään 4kpl paketeissa, 7,99€):
http://biltema.fi/ProductImages/17/large/17-612_l.jpg
Revin DID:stä meshin ulos ja avasin sen. Otin 2,5mm poranterän ja rullasin meshin uudelleen tuon poranterän ympärille (niin tiukaksi kun sain). Sitten hapetettiin n.20-30sec uudella töhöllä! Perkele mesh hehku koko matkaltaan keralla punasena ku liekki oli sen verran suurempi/tehokkaampi. Seuraavaksi 3xnesteen poltto ja mesh DIDiin poranterän kanssa. Pyöräyttelin coilit ympärille ja otin terän pois.
DID kiinni ProVariin (3.5V, 1.5Ω) nappi pohjaan ja silmät kiinni! :D
Kun uskalsin silmiäni vähän raottaa niin perkeles... missä E1 koodi?!? Miksi coili hehkuu tasaisen punaisena koko matkalta?!? WTF?!? Onnistuinko ensi yrittämällä??? KYLLÄ!!! :o
Nesteet sisään ja naatiskelemaan taas kumpupilvistä (ja nikotiini övereistä)! :laugh:
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
vanttila
Perusteluina on se, että setupin tekeminen on paljon helpompaa mekaanisella putkella kun ei hotspotin sattuessa tarvi erroreita katella. Ite tykkään vääntää about 0.8 ohmin setuppeja, jolloin ei suurin osa (yksikään) vv-putki suostu antamaan mitään virtaa, tai jos antaa niin se on 3.3V luokkaa. Putkimodilla saa sen 4V puskettua alkuun. Kicktulla putkella en kans tee mitään genesis-atojen kanssa, sillä aina on tehot yli 10W. Silica-virityksillä vv ja vw on oikeen toimiva, mutta genesiksillä mielestäni ei.
Yks vv on nyt tulossa mutta toisaalta nythän on hyvä tekosyy hankkia yks laite lisää :P Pitäsköhän sitä smokin telescopea ruveta tutkimaan :)
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
TrippyG
Ennen olen meshit töhötellyt sellaisella pienellä kaasukolvilla, missä ei kovin iso liekki ollut. Se taisi olla suurin hotspot yms ongelmien aiheuttaja, eli mesh ei hapettunut tarpeeksi (en hapettanut tarpeeksi pitkään).
Hyvällä toholla pääsee huomattavasti helpommalla ja kivuttomammin, eli +1
Tässä oma "tyylinäytteeni" mesh setupin teosta DID atoon:
http://www.youtube.com/watch?v=9wqJVZH50fM
Vs: Meshin käärintää ja vastuslangan virittelyä
video ei ole käytettävissä ???
Vs: Meshin käärintää ja vastuslangan virittelyä
Sori sori sori... ::) Olin vähän hätäinen ton linkin uppaamisen kanssa: "Videota käsitellään. Tarkista uudelleen muutaman minuutin kuluttua." Eli joku Youtube renderöinti vielä käynnissä.
Vs: Meshin käärintää ja vastuslangan virittelyä
Semmonen vinkkivinkki tohon didiin ja muihin isolla wick-reiällä varustettuihin genesiksiin. Täyttöruuvia ei tarvi avata didissä edes täyttöä varten, sen voi täyttää suoraan meshin läpi koska aukko on niin iso.
Aivan bueno arvostelu muuten. Mulla jää noi nestepoltot kokonaan välistä, mutta hyvin oli videossa käyty kaikki vaiheet läpi joista jokainen voi sitten oman tapansa löytää. Ei taida olla kahta ihmistä jotka setupin samalla tavalla vääntävät.
Meshin käärintää ja vastuslangan virittelyä
Vanttilan jutut saavat kyllä tuon ZAU vaikuttamaan houkuttelevalta vaihtoehdolta.
Vs: Meshin käärintää ja vastuslangan virittelyä
ZAU:sta ei oo kokemusta, mutta ZAGista ja ZAPista on. Hyviä atojahan ne on, kunhan vaihtaa isomman o-renkaan topcappiin että pysyy hattu tuulellakin päässä. Näissähän ei ole täyttöreiälle ruuvia, vaan reikä on kokoajan avoinna oleva 16G neulalle sopiva. Toki tuon reiän voi varmaan peittää ja uskoisin että silti wickaa, sillä wick-reikä taitaa olla isompi kuin didissä.
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
vanttila
Semmonen vinkkivinkki tohon didiin ja muihin isolla wick-reiällä varustettuihin genesiksiin. Täyttöruuvia ei tarvi avata didissä edes täyttöä varten, sen voi täyttää suoraan meshin läpi koska aukko on niin iso.
Kappas; suunnilleen saman neuvon heitin tänne. :D
Mites se meni; great minds think alike? :laugh: