-
Re: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Charunille virtuaalinen hatunnosto, paljon selkeitä vastauksia, myös foorumin muilla osa-alueilla... taitaa olla uusi guru syntymässä? :)
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Spheroid on kanssa harkitsemisen arvonen ostos. Etenkin ensimmäiseks korjattavaks. Todella helppo setupin teko ja tota ei ainakaan saa vuotamaan millään ilveelläkään ellei tarkotuksella ylitäytä. Miinuksena sit melko pieni nestetilavuus. Itte oon tykänny todella paljon ja toi on nyt jonkun aikaa kulkenu taskussa mukana kun poistun kotoota. Kayfun tuli nyt uudeks kotilaitteeks ja sitä voi kanssa näin päivän käyttökokemuksella suositella. Oli myös todella helppo saada toimimaan. Joillain ilmeisesti ollu pieniä ongelmia wickaamisen kanssa. eli tulee joko liian nopeesti nestettä ja alkaa vuotamaan tai sit tulee liian hitaasti nestettä ja antaa palanutta makua. Mä sain ton heti ekalla yrityksella pelittämään, mut voi tosin olla et kävi vaan tuuri :D
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
Charun
Noh.. KayFunin
Base Kitti maksaa 119.75€, että eipä se hirveesti Somniumia kalliimpi ole. Saatavuus on toki heikohkoa, kun on sen verran loistava laite että kaikki sellasen haluaa. :D
Nimenomaan tämä on pienoinen ongelma, kun ei satu olemaan se pari hunttia irrallista koko ajan.
Lainaus:
Alkuperäinen postaaja
Charun
Silicaan on meshiä helpompi tehdä setuppeja ja alkuun voi vaikka kokeilla ~10€ RDA:ta, niin pääsee jutusta kärrylle. Toki jos haluaa kerralla hyvän ja nimenomaan meshivehkeen, niin kyllähän Somniumin eriste jeesaa kummasti ja vaikuttaa muutenkin kaikin puolin hyvin suunnitellulta vehkeeltä. ;)
Jotenkin tullut siis johtopäätökseen näistä vehkeistä, että kannattaa hypätä alkuun altaan syvään päähän. :D Tiedä sitten, kannattaako. Mutta olen nyt päättänyt toimia näin. Hyvät vehkeet saa ainakin myytyä eteenpäin, jos ei luonnistu/miellytä.
Lainaus:
Alkuperäinen postaaja
Charun
Kaasulieden liekki ei ole riittävän kuuma kunnolliseen meshin tohotukseen.
Jollain videolla olin näkevinäni tällaista toimintaa. Sääli et Hullut Päivät meni jo, tarjouksessa oli myös Brulee-setti polttimen kera.
Lainaus:
Alkuperäinen postaaja
Charun
#500 taitaa tällä hetkellä olla se kovin juttu meshivehkeiden verkoksi. Kanthalin paksuus valitaan halutun vastusarvon mukaan: esim. 0.32mm Kanthalilla tulee 4 kierroksella resistanssiksi ~0.8ohmia, kun taas 0.2mm antaa samoilla kiekoilla ~2.3ohmia. ;)
Hotspot tarkottaa nimensämukaisesti "kuumaa pistettä", eli vastuslanka hehkuu (yleensä oikosulun seurauksena) yhdestä kohdasta selvästi kuumempana ja useimmiten palaa vielä poikki. Silicavehkeissä moisia ei juuri esiinny kuin vastuslangan osuessa runkoon, tai toisiinsa ja on hyvinkin helppo fiksata. Meshivehkeissä taitaa olla yleisin ongelma ja niissä useimmiten johtuu siitä, että vastuslanka ottaa meshin kautta maihin ja saattaa olla melko kettumainen korjata. ;)
All right. Kiitos näistä tiedoista molemmille. Liksapäivään on vielä pari viikkoa, eli vielä tarpeeksi aikaa vatvoa. :)
-
Vs: Re: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
Jalippo
Charunille virtuaalinen hatunnosto, paljon selkeitä vastauksia, myös foorumin muilla osa-alueilla... taitaa olla uusi guru syntymässä? :)
:-[
Mää mikään guru ole, kunhan yritän pistää hyvää kiertämään; itsekin aloittelijana täältä sen verran paljon informaatiota sain, että koin asiakseni sotkea lusikkaani muidenkin soppaan. :D
Lainaus:
Alkuperäinen postaaja
philo
Nimenomaan tämä on pienoinen ongelma, kun ei satu olemaan se pari hunttia irrallista koko ajan.Jotenkin tullut siis johtopäätökseen näistä vehkeistä, että kannattaa hypätä alkuun altaan syvään päähän. :D Tiedä sitten, kannattaako. Mutta olen nyt päättänyt toimia näin. Hyvät vehkeet saa ainakin myytyä eteenpäin, jos ei luonnistu/miellytä.
Totta tietysti tuokin; jos ei Somnium sytytä, niin tuskin tostakaan paria kymppiä enempää takkiin tulee, jos ei maistukaan ja laittaa myyntiin. :)
Lainaus:
Alkuperäinen postaaja
philo
Jollain videolla olin näkevinäni tällaista toimintaa. Sääli et Hullut Päivät meni jo, tarjouksessa oli myös Brulee-setti polttimen kera.
Toi brulé poltin on tehojensa puolesta vähän siinä ja tässä: mulla on vastaava toho ja sillä kyllä saa melko pitkään hiillostaa, että kuumenee riittävästi.. :-\
Kannattaa esim. rautakaupoista, Biltemasta, Motonetistä, Claes Ohlsonilta ym. tutkailla; yleensä löytää muutamalla kympillä vaihtopulloja syövän, riittävän tehokkaan tohottimen. ;)
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
hesekiel
Arizonan cobra -kopion kanssa tuli hirvee tappelu. Ihan sama miten meshin polttelee, koko ajan tulee hotspottia. Mitä ihmettä ton kanssa pitäis tehä? En ymmärrä.
Tähän asti olen kokeillut tolla mukana tulleella, ohmeista päätellen .30 kanthalilla. En tiiä mitä laatua, mutta voiko johtua kanthalin paskasta laadusta, ettei homma skolaa?
Ei siis mitään kokemusta genesiksistä, mutta teoriatasolla tiedän kyllä miten tuo tehdään. Kiina-kopio-kiina tietysti tuo oman lisätwistinsä, mutten ymmärrä miten sekään aiheuttaisi jatkuvaa hotspottia, jos muu olisi kunnossa.
joo o. ei olluna mullakaan ton kanssa heleppoa. :D siinä valmiissa setupissa poikkes lanka samantien. polttelin sit sitä valmis messiä aika virtun monta kertaa. sain työkaluväännön, muutaman kalja sun muun jälkeen 1.2 ohmin setupin. porasin ilmaaukkoaki isommaksi.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Ei mitään asiaa, mutta merkkaan tämän langan itselleni seurattavaksi. Paljon on tässä aiheessa oppimista...
-
Re: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Miten lanka merkataan seurattavaksi? Tapatalk?
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Kirjoittamalla ko. lankaan jotain. Tällöin voit seurata ketjua tuolta "Näytä uudet vastaukset viesteihisi"- kohdasta.
-
Re: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Ok nyt ymmärsin, kiitoksia.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Minkälainen toho pitäisi vakavamielisellä harrastajalla olla?
Onko tämmönen mitään? http://www.clasohlson.com/fi/Kaasupoltin/Pr307115000
-
Re: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Tota on täällä kehuttu, pitäisi olla vähintääkin riittävä.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Tohosytkärikin ajaa tuossa jo asiansa ja niitä saa jokaisesta halpahallista.
Esimerkiksi reilun kympin "Iroda AT-2056 Butajet" toimi vuosia tämän entisen tupakkamiehen ainoana sytkärinä.
Kokemuksesta voin sanoa että tuo venyy oikeasti myös pieniin kovajuotoksiin.
http://tuontitukku.fi/tuote/iroda-ka.../742286205600/
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
jarif
Mulla on tuollainen http://www.kouluelektroniikka.fi/cgi...did=7270%20770
Hyvin on pelannut...
Ei tämäkään huono vaihtoehto ole...tulee mukana jos jonkinlaista härpäkettä. http://www.kouluelektroniikka.fi/cgi...did=7310%20800
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
hesekiel
Arizonan cobra -kopion kanssa tuli hirvee tappelu. Ihan sama miten meshin polttelee, koko ajan tulee hotspottia. Mitä ihmettä ton kanssa pitäis tehä? En ymmärrä.
Tähän asti olen kokeillut tolla mukana tulleella, ohmeista päätellen .30 kanthalilla. En tiiä mitä laatua, mutta voiko johtua kanthalin paskasta laadusta, ettei homma skolaa?
Ei siis mitään kokemusta genesiksistä, mutta teoriatasolla tiedän kyllä miten tuo tehdään. Kiina-kopio-kiina tietysti tuo oman lisätwistinsä, mutten ymmärrä miten sekään aiheuttaisi jatkuvaa hotspottia, jos muu olisi kunnossa.
Tossa cobrassa on pari hankaloittavaa ongelmaa. Ensimmäinen on, että plussa ja miinus on tosi kaukana wick-reikästä, jolloin pätkä wickiltä navoille on sen verran pitkä, että näitä nämä pätkät on tosi vaikea pitää märkinä, jolloin kurkkutuntuma on aina hieman kovempi. Toinen on, että tuo wick-reikä ei ole eristetty eikä se siltikään ole kovin iso. Tämä tekee haasteita isomman keskireiän tekemiseen samalla, kun meshwick ei saisi olla älyttömän kireästi reiässä.
Ensiksi lähtisin selvittelemään, johtuuko hotspot siitä, että vastuslanka käy siitä kohtaa kuivana, vai siitä, että se lyö maihin meshwickkiin. Mistä kohtaa hotspot sijaitsee? Mikäli kyseessä olisi huonolaatuista vastuslankaa, se löisi kyllä lähes varmasti itsensä poikki, mikäli kyse on maihinvedosta.
-
Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Joku langoista paremmin perilläoleva voisi väsätä vaikka GoogleDocsiin jonkin sortin yhteenvedon eri langoista, josta kävisi ilmi paitsi paksuus myös AWG-vastaavuus ja vastusarvo/metri.
Tai sitten linxor, tack!
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Ylivuodon laskurista löytyy nuo tiedot (coil calc välilehdestä)
-
Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Kappas, missannut koko laskurin!
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Täytyy taas kysellä viisaammilta, minkälainen wickki kannattaa tehdä paksuhkolle nesteelle? Käytössä on ainoastaan 400-meshiä.
Uusien nesteiden kanssa ongelmissa, tehny useamman "erikokoisen" wickin (vaihdellu wickin keskireiän ja seinämien kokoja, sekä testannu jopa vaihtaa wickin muotoa suorasta hieman suipoksi) eikä mikään noista tunnu saavan noita paksumpia nesteitä coileille asti.
Coili itsessään hehkuu nätisti koko matkalta ja on wickin ympärillä "pehmeästi" eli ei pureudu wickin sisään, ei hotspotteja tai muuta.
Sekava viesti, mutta toivottavasti joku ymmärsi, mitä ajoin takaa. :-\
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Melko suuri keskireikä on taikasana tuolle #400 meshille, mutta helpoin olisi ilmeisesti umpinainen tanko #500 meshistä.
Sekin kannattaa huomioida, ettei coili ole liian "pehmeästi" ympärillä, eli koskettaa kuitenkin joka kohdasta meshiä.
Mikäli ei vaan wickkaa, niin sit ei auta muu kun kallistella modia vaakasuoraan aina vapotellessa.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
Jalippo
Melko suuri keskireikä on taikasana tuolle #400 meshille, mutta helpoin olisi ilmeisesti umpinainen tanko #500 meshistä.
Sekin kannattaa huomioida, ettei coili ole liian "pehmeästi" ympärillä, eli koskettaa kuitenkin joka kohdasta meshiä.
Mikäli ei vaan wickkaa, niin sit ei auta muu kun kallistella modia vaakasuoraan aina vapotellessa.
Tämä autto, kiitos! Vähän rapiat 1,4 millia ku jäi keskireiän kooksi ja muuten mahdollisimman ohut wickki, niin toimii. Kiitos vielä toisen kerran! :esmoke: