Täytyy huomenna varmaan makita kaivaa.. igluun uppos 1,5mm wurthin terä kyl mukavasti.
Printable View
Täytyy huomenna varmaan makita kaivaa.. igluun uppos 1,5mm wurthin terä kyl mukavasti.
Ilman kuristusta ja isompaa ilmareikää RSST on vain yksi halppisgenny muiden joukossa, tosin helppo semmoinen. Modattuna varsin mainio laite. 1.5mm rööri on kyllä todella ilmava. Itsellä 1.2mm ja 0.8mm röörit ja ehkä liian ilmava. Pieniä reikiä on helpompi suurentaa jos ahistaa. Reikien pienennys onkin sitten hiukka hankalampaa.
Nii joo tosiaan se kuristuspala.. Päässy tässä tohinassa unohtumaan sekin viritys. En kyllä tähän lähde tota 1,5mm reikää tekemään. Täytyypi tutkia ja funtsailla seuraavaa liikettä. :D
EDIT: toisen 1mm reiän poraaminen orkkisen yläpuolelle varmaan aika peliliike?
0.8mm suosittelen jos ahistaa niin sen isonnat sitten 1mm
ja muista sitten kierrokisa kun rupeat poraamaan.
tollanen n.1mm terä vaatii todella paljon kieroksia jotta leikkaa hyvin,itse vedellyt paineilma käyyttöisellä poralla kieroksia noi 25tuhatta menee muuten kun se kuuluisa sanonta kuuma veitsi voihin :)
Tuollaset kierrokset tekis höpöä, mutta ei oikein kerrostalokämppään paineilmatyökaluja, ja akkuporakoneista nyt irtoaa mitä irtoaa.
Onneksi on tuo pienoisporakone joka vapaana antaa edes 8000-10 000 RPM.
Edit.
Meikäläisellä on 2*1mm röörit, ja imu on tiukempi ku yhellä 1,5mm röörillä. Että miten vaan, ei tuu kallis vahinko, ja tuossa puhutaan kuitenkin suhteellisen marginaalisesta erosta (:
Perskeles, taitaa tuossa wurthin teräsarjassa 1mm olla se pienin. Duunissakaan en noin pieniä teriä tarvi niin ei viitti "firman piikkiin" käydä hakemassa. Noo rautakaupasta niitä saa. Eli 0,8mm terää hakemaan. On sitten se millinen valmiina jos siltä tuntuu. Täytyy varovasti tuolla makitalla kokeilla...
Jo on vaikeaa löytää o-renkaita jotka olis tarpeeksi ohuita tuon kannen pitimiksi, maailma kyllä täynnä renkaita mutta kaikki liian paksuja, .....kele !
Laitoin tuohon nyt ylipaksun o-renkaan ja naputtelin kannen paikolleen, renkaasta leikkauttui siivu pois mutta tulipahan tiukka sovite, ei ainakaan itekseen irtoile mutta olishan tuohon mukava saada jostain sopivakin kun nyt kannen saa kammeta oikein voimalla irti.
Tuli kyllä mukana mutta mihin sen laitoin, eipä löydy tähän hätään, annetaan olla nyt tuo tiukempi paikoillaan, luulen että taitaa olla jopa parempi ja jos tuo vielä hiukan tuosta löystyy.. :thinking:
Kaivoin makitan autosta ja ajattelin täräyttää kerralla sitten toisen 1mm reiän. Noh 1mm terä liian pieni tuohon makitaan. Otin sitten terän käteen ja rassailin tuota orkkis reikää hieman ja johan parani. Eipä tuo hirvesti tuosta suurentunut, mutta pienikin muutos näköjään vaikutti aikas reilusti. Nyt tuntuu sen verran mieluisalta, että lähtee käyttöön! Jää reikien poraamiset toistaiseksi tähän. Kuristeteen kun joskus saan niin katotaan sitten taas. :)
Pitänee itsekkin huomenna suurennella vakioreikä 1mm kokoon.
Somnium ampuu niin äkäisesti RSST verrattuna, setuppi on muuten aikalailla sama.
Onhan noi eri hintaluokan vehkeitä, mutta en muuta eroa keksi kuin tuon eri kokoisen reian tuoman edun.
1,2mm reiällä, ja folio kuristuksella(palaa odotellessa) sanoisin, ettää tää vetää vertoja ihan mille tahansa gennylle.
Loisto kampe ja hintaluokassaan voittamaton.
Kyl tähän saa tehtyä setupin erittäin helposti. Ei UD AGI ollu näin helppo. Vajaa 10min ku mesh wick laitettu rsst ja coili rakennettu ympärille. Peukkua tälle laitteelle.
Onko joku keksiny kuristusta kotikonstein? Esim foliosta yms.
eikös joku cartotankin päädystä tehnyt silloin joskus?
Elämäni toinen mesh-setuppi pyöräytelty. 5cm paksusti 400 meshiä,ontto putki. kääritty silleen että juuri mahtuu wickireiästä sisään. 0,32kanthaalia ja 0,7ohmia. kurkkutuntumaa ei juuri lainkaan,ja maistuu lähinnä kärylle ja roiskii nestettä melko lailla.hotspotteja ei havaittavissa. mikä mättää?
Liite 10151Liite 10152Liite 10153
Pitkä väli plussalla, mesh saa olla lähes kiinni tolpassa. Se hehkuu herkästi... muuten näyttää ihan hyvältä. Räiskyminen=ylivickkaus tai alitehot :)