-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
En mitään yleisesti Genesis -atoille suunnattua ketjua löytänyt, joten taitaapi sopia tänne:
Onko näissä paljonkin horizontal coilille suunniteltuja versioita? Eli siis coili olisikin vaakatasossa pystysuoran sijasta? Moisiin en ole ikinä törmännyt. Kun eniten näissä harmittaa tuo hatun suuri koko, ja suuri koko muutenkin suhteessa nestekapasiteettiin. Coilin voisi tehdä vaakatasoon samanlaisten napojen väliin, Jos meshistä taiteilee ikään kuin J kirjaimen muotoisen. Ehkä hieman hankalampaa kuin suora, mutta onhan niitä U -wickejäkin meshistä tehty, ei mitenkään mahdotonta. Tämä mahdollistaisi HUOMATTAVASTI pienemmän hatun, ja korkeuden. Itse nestetankille jäisi näin ollen saman kokoisessa laitoksessa paljon enemmän tilaa.
http://i6.aijaa.com/t/00867/11156685.t.jpg http://i10.aijaa.com/t/00483/11156686.t.jpg
En tosin tiedä, wickkaako mesh tuommoisessa käyrässä yhtä hyvin, mutta miksi ei wickaisi?
Ei mulla muuta... ::)
-
Re: Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja hesekiel
En mitään yleisesti Genesis -atoille suunnattua ketjua löytänyt, joten taitaapi sopia tänne:
Onko näissä paljonkin horizontal coilille suunniteltuja versioita? Eli siis coili olisikin vaakatasossa pystysuoran sijasta? Moisiin en ole ikinä törmännyt. Kun eniten näissä harmittaa tuo hatun suuri koko, ja suuri koko muutenkin suhteessa nestekapasiteettiin. Coilin
voisi tehdä vaakatasoon samanlaisten napojen väliin, Jos meshistä taiteilee ikään kuin J kirjaimen muotoisen. Ehkä hieman hankalampaa kuin suora, mutta onhan niitä U -wickejäkin meshistä tehty, ei mitenkään mahdotonta. Tämä mahdollistaisi HUOMATTAVASTI pienemmän hatun, ja korkeuden. Itse nestetankille jäisi näin ollen saman kokoisessa laitoksessa paljon enemmän tilaa.
http://i6.aijaa.com/t/00867/11156685.t.jpg http://i10.aijaa.com/t/00483/11156686.t.jpg
En tosin tiedä, wickkaako mesh tuommoisessa käyrässä yhtä hyvin, mutta miksi ei wickaisi?
Ei mulla muuta... ::)
Sähköpössymies tuolla "unelmiesi atomisaattori" aiheessa kehittelee juurikin tämän tyylistä diy rta:a. On kyllä mielenkiintoinen kehitelmä siis positiivisessä mielessä :)
Edit: tarkennuksena vielä että ei ihan samalla idealla mutta tuotakin setuppia voisi varmaabkin kokeilla vaikka ei varmaankaan ole tarvetta koska paperilla hänen systeeminsä voi käyttää silikaa ja meshia riippuen käyttäjän mieltymyksestä.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Eikös toi pissi tankin tyhjäksi?
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Ei kai se kapilaari ilmiö niin vahva ole tuossa, että se tankin imis tyhjäksi, vai miten meinasit?
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Sitäpä juuri, valuuhan se neste tosta läpi helpommin, kuin pystywikistä.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Tulisi se kai pystywickistäkin yli jos niin voimakas olisi. Mielestäni tota kannattaa kokeilla, pituutta saa helposti 1cm, ehkä kaksin pois.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Varma ei tietenkään olla, mutta jostain lukenut noiden J-wikkien ominaisuuksista. Eikös tollainen ole Delin Maxissa ja Minissä?
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
Troll from behind
Varma ei tietenkään olla, mutta jostain lukenut noiden J-wikkien ominaisuuksista. Eikös tollainen ole Delin Maxissa ja Minissä?
Toinen vaihtoehto tehdä U mikä wickkaa molemmilta puolilta. Vai riittääkö meshin hengityskyky kapillaari-ilmiön aikaansaamiseksi?
-
Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Kertauksen vuoksi, mutta mikäs on se minimi/optimaali reikä hyvään wikkaukseen?
Onko tuossa muuten mitään korrelaatiota wickin pituuteen, eli reiän koko kasvaa suhteessa wickin pituuteen ?
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Varmaan useimpien kysymysten kerhoon kuuluva.
Kanthal A-1 vai D, kumpaa siis laittaa ostaen?
Onko tuolla käytännössä mitään eroa?
A-1: http://viewitem.eim.ebay.fi/Kanthal-...798897134/item
resistance at 20°C: 43.48 ohm/m
D: http://viewitem.eim.ebay.fi/Kanthal-...791435600/item
resistance at 20°C: 43.50 ohm/m
0.12 ohm eroa tuskin tuntuu missään coilissa ??
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
^Ero on lähinnä lämmönkestossa; A-1 kestää paremmin hotspotteja. Silican kanssa ei taida olla käytännössä eroa. ;)
-
Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Osta sitä A-1tä, on imo järeämpää tavaraa helpottaen käsittelyä ja väittäisin, että ei ole niin altis katkeamaan mekaanisesti, koska työstöjännitys ei tee yhtä hallaa kuin D-laadulle.
Sehän OLI tiedossa, että tuo sytkällä polttelu paitsi puhdistaa, myöskin poistaa työstöjännitystä.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
Charun
^Ero on lähinnä lämmönkestossa; A-1 kestää paremmin hotspotteja. Silican kanssa ei taida olla käytännössä eroa. ;)
Silica käyttöön juu.
Lainaus:
Alkuperäinen postaaja
Troll from behind
Osta sitä A-1tä, on imo järeämpää tavaraa helpottaen käsittelyä ja väittäisin, että ei ole niin altis katkeamaan mekaanisesti, koska työstöjännitys ei tee yhtä hallaa kuin D-laadulle.
Sehän OLI tiedossa, että tuo sytkällä polttelu paitsi puhdistaa, myöskin poistaa työstöjännitystä.
On tiedossa, mutta ei ole jaksanut vaivautua kaivamaan sytkäreitä esille :D
Laitoin nyt kuitenkin ihan hinnan takia D:tä tulemaan. Parin euron hintaero ratkaisi.
-
Vs: Re: Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
MPKO
Sähköpössymies tuolla "unelmiesi atomisaattori" aiheessa kehittelee juurikin tämän tyylistä diy rta:a. On kyllä mielenkiintoinen kehitelmä siis positiivisessä mielessä :)
Edit: tarkennuksena vielä että ei ihan samalla idealla mutta tuotakin setuppia voisi varmaabkin kokeilla vaikka ei varmaankaan ole tarvetta koska paperilla hänen systeeminsä voi käyttää silikaa ja meshia riippuen käyttäjän mieltymyksestä.
Tämä on hieman viivästynyt kun tuli muuta koneistettavaa, mutta kyllä se valmistuu aikanaan. :-\
Ajattelin lähes samaa, mutta vien wickin takaisin tankkiin muodostaen U:n eli wickaa molemmista päistä mutta pysyy silti matalana ja ei vuoda keskireijästä koska molemmat reijät on tankissa.
Hatusta on tarkoitus tehdä matala ja siksi siihen tulee kierteet.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Mistähän semmosen skidin kuusiokoloavaimen löytäs tähän hätään? Minkä kokosta noi atot yleensä käyttää
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
mulqvist
Mistähän semmosen skidin kuusiokoloavaimen löytäs tähän hätään? Minkä kokosta noi atot yleensä käyttää
Jos on tosi akuutti tarve ni välttävän työkalun saa tasapäämeisselistä viilan avulla. Monet torx-päät sopii myös kuusiokoloihin.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Kannattaako ensirebuildableksi hankkia Somniumin? Kiinnostaisi kovasti suosia suomalaista. Onnistuukohan meshin poltot yms esimerkiksi kaasuliedellä? Ja kuinka tiheätä kannattaa hankkia? Entä Kanthalit sitten, kuinka paksua? Vai onko tämä aivan liian haastavaa, ja kannattaa pysyä poissa?
Omat päätelmät tästä skenestä:
Silica:
+helpompi tehdä setup
-kalliimpi (Kayfun/Penelope yms.)
-saatavuus (samat kuin yllä)
Mesh:
+halvempi hinta (Somnium)
+saatavuus (sama)
-meshin hapetus näyttää hankalalta (Creme brulee-polttimia ja muuta erikoisjutskaa)
-mitä tarkoittaa hotspot?
Korjatkaa jos olen aivan metsässä. Yritin katsella tuota "meshin käärintää yms"-topicia, mutta tipuin kärryiltä.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Arizonan cobra -kopion kanssa tuli hirvee tappelu. Ihan sama miten meshin polttelee, koko ajan tulee hotspottia. Mitä ihmettä ton kanssa pitäis tehä? En ymmärrä.
Tähän asti olen kokeillut tolla mukana tulleella, ohmeista päätellen .30 kanthalilla. En tiiä mitä laatua, mutta voiko johtua kanthalin paskasta laadusta, ettei homma skolaa?
Ei siis mitään kokemusta genesiksistä, mutta teoriatasolla tiedän kyllä miten tuo tehdään. Kiina-kopio-kiina tietysti tuo oman lisätwistinsä, mutten ymmärrä miten sekään aiheuttaisi jatkuvaa hotspottia, jos muu olisi kunnossa.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
philo
Kannattaako ensirebuildableksi hankkia Somniumin? Kiinnostaisi kovasti suosia suomalaista. Onnistuukohan meshin poltot yms esimerkiksi kaasuliedellä? Ja kuinka tiheätä kannattaa hankkia? Entä Kanthalit sitten, kuinka paksua? Vai onko tämä aivan liian haastavaa, ja kannattaa pysyä poissa?
Omat päätelmät tästä skenestä:
Silica:
+helpompi tehdä setup
-kalliimpi (Kayfun/Penelope yms.)
-saatavuus (samat kuin yllä)
Mesh:
+halvempi hinta (Somnium)
+saatavuus (sama)
-meshin hapetus näyttää hankalalta (Creme brulee-polttimia ja muuta erikoisjutskaa)
-mitä tarkoittaa hotspot?
Korjatkaa jos olen aivan metsässä. Yritin katsella tuota "meshin käärintää yms"-topicia, mutta tipuin kärryiltä.
Äkkiseltään sanoisin sen olevan "aika" hyvä. :D
Muuhun en ota kantaa mutta hotspot meinaa sitä, että meshi maadottaa ja tulee oikosulku.
-
Vs: Aloittelija kysyy ; "Mitä ihmettä, auttakaa?"
Lainaus:
Alkuperäinen postaaja
philo
Kannattaako ensirebuildableksi hankkia Somniumin? Kiinnostaisi kovasti suosia suomalaista. Onnistuukohan meshin poltot yms esimerkiksi kaasuliedellä? Ja kuinka tiheätä kannattaa hankkia? Entä Kanthalit sitten, kuinka paksua? Vai onko tämä aivan liian haastavaa, ja kannattaa pysyä poissa?
Omat päätelmät tästä skenestä:
Silica:
+helpompi tehdä setup
-kalliimpi (Kayfun/Penelope yms.)
-saatavuus (samat kuin yllä)
Mesh:
+halvempi hinta (Somnium)
+saatavuus (sama)
-meshin hapetus näyttää hankalalta (Creme brulee-polttimia ja muuta erikoisjutskaa)
-mitä tarkoittaa hotspot?
Korjatkaa jos olen aivan metsässä. Yritin katsella tuota "meshin käärintää yms"-topicia, mutta tipuin kärryiltä.
Noh.. KayFunin Base Kitti maksaa 119.75€, että eipä se hirveesti Somniumia kalliimpi ole. Saatavuus on toki heikohkoa, kun on sen verran loistava laite että kaikki sellasen haluaa. :D
Silicaan on meshiä helpompi tehdä setuppeja ja alkuun voi vaikka kokeilla ~10€ RDA:ta, niin pääsee jutusta kärrylle. Toki jos haluaa kerralla hyvän ja nimenomaan meshivehkeen, niin kyllähän Somniumin eriste jeesaa kummasti ja vaikuttaa muutenkin kaikin puolin hyvin suunnitellulta vehkeeltä. ;)
Kaasulieden liekki ei ole riittävän kuuma kunnolliseen meshin tohotukseen. #500 taitaa tällä hetkellä olla se kovin juttu meshivehkeiden verkoksi. Kanthalin paksuus valitaan halutun vastusarvon mukaan: esim. 0.32mm Kanthalilla tulee 4 kierroksella resistanssiksi ~0.8ohmia, kun taas 0.2mm antaa samoilla kiekoilla ~2.3ohmia. ;)
Hotspot tarkottaa nimensämukaisesti "kuumaa pistettä", eli vastuslanka hehkuu (yleensä oikosulun seurauksena) yhdestä kohdasta selvästi kuumempana ja useimmiten palaa vielä poikki. Silicavehkeissä moisia ei juuri esiinny kuin vastuslangan osuessa runkoon, tai toisiinsa ja on hyvinkin helppo fiksata. Meshivehkeissä taitaa olla yleisin ongelma ja niissä useimmiten johtuu siitä, että vastuslanka ottaa meshin kautta maihin ja saattaa olla melko kettumainen korjata. ;)