Ei ole kyllä floodannut vielä tähän päivään mennessä (paitsi jos jättää kammion kupin liian löysälle).
Ja kai sen jollain putkella siihenkin sais. :D
Printable View
Ei ole kyllä floodannut vielä tähän päivään mennessä (paitsi jos jättää kammion kupin liian löysälle).
Ja kai sen jollain putkella siihenkin sais. :D
Milloin ja mitä näitä saa??
Kantsii laittaa ostoilmoa myös tänne forkalle, itselle tuli parikin tarjousta heti kättelyssä, kiitos asiallisten kaverien :)
Kertokaas viisaammat että minkä kokosta vaijeria ootte käyttänyt taifunin kanssa? Niin ettei vuoda jne. Vehjes olis mulle matkalla :) ja mietiskelin että pitäiskö tilata vaijeria kokeeksi? Vai onko edes hyötyä? Pyöritteleekö mielummin vaan pelkän mesh rullan?
En oo ihan varma miten pitkä pätkä sitä tulis, mutta saattaa olla niin lyhyt että on vähintään hankala onnistua ilman että purkautuu. Eiköhän se pöhise ihan kiitettävästi ihan silicalla/pumpulilla/meshillä. (:
Itsellä ainakin vaijeri lähti pahasti purkautuu vaikka yritin teipata ennen leikkausta. Laitoin ihan meshistä tehden umpipötkön #400 meshiä, ja toimi ihan heittämällä.
2mm vaijeri taitaa olla nyt sisässä, meinasi lähteä purkautumaan, mutta sen verran meshiä koko matkalta päälle että on piukasti urissa ja käärii sinne meshin sisään takas kasaan vaijerin. Se tuntuu korjautuvan samalla pyörittelyllä kuin meshi tiukkenee. Ja mitä tuossa uuden setupin tein, niin vaijeri pätkä pysyi kasassa.
Taifuni kotiutu tänään ja eka setuppi pyörätetty. Tein #500 mesh tukin joka mahtui juuri "hahlojen" väliin ja hyvin pöhisee. En laittanut silicaa päälle, eikä ainakaan vielä ole vuotanut nesteitä pihalle. Oli kyllä todella helppo setupoitava :)
Perhana kun työ hehkutatte!
Mielenkiintoa olisi kokeilla tätä, ainakin materiaaleissa ei ole kysymysmerkkejä, tuossa Squapessa hitusen tuo alumiinipinnoite arveluttaa, koska sopivuudesta on vain valmistajan sana, mutta rosteriin voi aina luottaa!
(Vaikkakin lyö kipinää joskus :D)
Mjooh, mutta odottelen ensiksi lisätietoja Deliltä tuosta materiaalista.
Squapesta ei ole kuin kuvia, mutta kyllä mä speksien valossa valitsisin Taifunin. Siinä on muutama oikeasti paljon viksumpi veto tehty tossa rakenteessa, että se kuppi Squapessa pelkästään ei paljoa auta.
No juu, helpompi täyttö, ei ole ilmarööri 510-connectorissa. Ei ole kyllä tosin squapekaan valutellut mitä kolmisen tankillista kohta imenyt tästä, siinäkin tais hieman kohollaan olla toi ilmaaukko kammiossa, jos en väärin muista, ei jaksa coilin alle kurkkia. :) Taifuniin pitäis kyllä toi isompi ilmaputki hommata.
Juuri vaihdoin normaalin tilalle tuon loosen (1.5m) ja on kyllä huomattavasti mukavampi. Imuvastus abouttiarallaa kayfun liten tasoa...
Menee täysin makuasioiksi, mutta mun mielestä toi 1.2mm ilmatuubi joka tulee vakiona oli enemmän kuin passeli. 1.5 ja sitä isommat viilentää aivan liikaa höyryä :D
Makuasioita joo :) Itse en huomaa ton 1.2 ja 1.5 välillä höyryn lämmössä juurikaan eroa, mutta ei tartte imailla nii posket lommolla ;)
Onneksi hommasin Taifunin. Ei tästä ja foggerista voi kyllä oikein puhua samana päivänä. Taifun toimii just niinku se on suunniteltu käytettäväksi, ei tartte kikkailla sen atokammion kannen kireydellä niinkuin foggerissa. Setupin teko on todella helppoa, kiitos nerokkaan laskettavan kauluksen. Ei haittaa vaikka on noin 90€ kalliimpi, on kyllä joka sentin arvoinen.
3 mm ekowool on kuin tehty tätä varten. 0,8 ohmin setuppi ja mekaanisella täyttä höyryä. Pakko hehkuttaa saatana.
Mä tuuttasin 3x2mm ekowoolit tänään pykälään ja kyllä vaan toimii! 3/4 kieppiä 0.32 narua ja tasan 1 ohm. jaksaa meksulla ajella todella komeasti!
Loistava ato, ihmettelen kuinka se nyt vasta on eksynyt omiin käsiin. Ihan heti ei pois anneta vaan tilataan toinen perään!