Enemmän tehoo=enemmän höyryä:esmoke:
Printable View
Enemmän tehoo=enemmän höyryä:esmoke:
vähemmän pinta-alaa=vähemmän höyryä.:esmoke:
1.2-1.8 ohmia on mielestäni se optimi alue.
Raaka-Eki, mitä vähemmän se putki hukkaa sitä jännitettä jonnekki matkan varrella niin sitä parempi.
Mutta mikäs siinä jos haluat että 20% energiasta menee napin lämmitykseen.
Niin ja mieluummin mä kerran viikossa otan palan hiekkapaperia ja käytän viisi minuuttia aikaani kontaktien putsaukseen kuin turhaan lämmitän nappia, mun sormi tekee sen jo valmiiksi. 1.5ohmin kartokin höyryää 4voltilla paljon kivemmin kuin 3,4voltilla :esmoke:
Ja kun kerta pinta-alaa halajat niin käytä paksumpaa vastuslankaa sitten. Itsellä 0.25mm ollu käytössä tähän asti ja tuolla saa oikein näppärästi sen 0.8-1.2ohm, perjantaina tilasin 50m kelan 0.32mm.
Itellä se optimialue akkujännitteellä liikkuu 0.5-1.2ohm alueella. Tällöin täydellä akulla saa sellasen 12-25w tehoja :esmoke:Mutta mikäs siinä jos tykkää laimeista höyryistä, toinen tykkää äidistä, toinen tyttärestä, kolmas... Äiteeni höyryää 1,5ohmin dual coil kartoa twistillä ~3.6voltilla ja on erittäin tyytyväinen.
Missäpäin vaikutat? Jos vaikka verrataan putkiamme.
koskt, mitä akkuja käytät? Etteivät vain olisi elämänsä päässä?
Mielipiteet on kuin perseenreikiä.. Jokaisella sellainen löytyy, mutta ei se tarkoita että toisten tarvitsisi sinun _siitä_ pitää :D
Suoraan akkujännitteellä 0,8ohm-1,1ohm pelittää mainiosti pidempään (painotus -> IMO)
You must be new here?
Kaik alle ohmisia settejä >>>
nimbus atomizer / mortar V5 by edz / vapor train berry trails 40pg/60vg - dual coil 28ga kenthal, 3loops @ .3 ohms
http://www.youtube.com/watch?v=kZy1LxD50FU
DID on a silver bullet, 28g nichrome 5 wrap 0.7ohm
http://www.youtube.com/watch?v=Dw03fFmcjHw
60/40 vg/pg ~0.24ohm Quad coil
http://www.youtube.com/watch?v=y5gNxn43qUM
Alhaiset ohmit ei välttämäti tarkoita pienempää kosketusta :esmoke:
Ei pidä hermostua. Toki voit hioa putkeasi niin paljon kuin haluat, ei se minua häiritse.
Omassani ei nappi lämpene, eikä muitakaan ongelmia ole ollut.
Ehkä tämä putki onkin erikois kappale ja teidän ongelmat ovat todellisia. Ei voi tietää.
Asustelen Torniossa. Jos olet täälläpäin liikenteessä voin kahvit keittää.:)
mielipiteet todella ovat kuin persereikiä.
Voi kuule hyvinkin olla. Jos akkua rääkätään niin se menettää virrananto kykyänsä. Ja mitä vanhempi akku on (lue lataus/purku syklejä) niin sitä heikommin se pitää latausta.
Ja se on ihan todistettu moneen kertaan että Efestit kyykkää kovassa kuormassa enemmän kuin AW. Siksi AW>Efest mekaanisten putkien kanssa.
Akku testaus sivuja on monia mutta itse lueskelen Flashlight information ja AkkuDB
Itse en Efestejä omista kuin 2kpl 18350 koossa, ne omistan Vamoa varten. Yhden AW IMR 18650:an omistan ja sitä käytän hapettamatton setupin teon pulssitteluun. 18350 AW IMR:ää käytän kylillä ja kotona ensisijaisesti käytän noita vihreitä Samsungeja (INR18650-20R) tai Panasonicin NCR18650PD akkuja, suuri virrananto kyky ja jännite ei notkahda paljoa kovassa kuormassa.
taitaa mennä vähän pulun nussimiseksi...
Raapasimpa itekkin kontaktit puhtaaks ja tulittaa reippaasti paremmin. Toiminta on muutenki tasasempaa, ennen tuunausta otti kunnolla kontaktia vaan sillontällön.
Natural + RSST-ato ja siinä A1 28Awg kanthaalista 0,8 ohmin setup ja
helevetin hyvin pöhisee :o
- JJ
Täytyy kanssa toi RSST hommata kokeeks. Sopii aika nätisti naturaaliin.
Jahas, lukeman perusteella vissii joutuu tän laitoksen hommaamaan itelle matala ohm setuppien toivossa....
Natural & RSST kaikki oleelliset pinnat hiottuna, 0.8 ohmia, droppia 4.17 -> 4.00
510 liitin madallettu, ei jää rakoa. vielä pitäisi koko yläcappi hiota tasaiseksi, joku 1.x millin pyöristys joka pistää silmään :D
Hieman himottaisi yrittää laittaa putken yläcapin törkeät poratut pallurat piiloon, sillä saisi jo aikalailla hybridi näköä.
Siinä on kyllä asiallinen tulos.
Mutuilen mutta oma AGA-T2+ taitaa jonnekin hukata tehoja. Noh, näkee sen sitten kun DID D20, toivottavasti loppuviikosta olis täällä :P