Kiinnostais tietää millasta arvoo ProVari antaa verrattuna vaikkapa 2.1 lavaan.. *vink vink* ;)
Printable View
Kiinnostais tietää millasta arvoo ProVari antaa verrattuna vaikkapa 2.1 lavaan.. *vink vink* ;)
Mitenköhän se mittaa tuota pulssia. Luultavasti mittaus frequenssi on liian hidas ja samppeleiden määrä jää alhaiseksi jolloin keskiarvoistus menee pieleen alussa...
4 voltin asetuksella 4 volttia. Provarista tulee ulos tasavirtaa eikä pulssia. Sama kuin lava 1, lambo ja lava 4.Lainaus:
Alkuperäinen postaaja hesekiel
Privaviestittelyä with the maker
Siinä vastauksen tynkää niin MPKO:lle, kuin overflow:lle ja kysymystä halutaanko infot kotimaisiksi vai as-is?
Lainaus:
Alkuperäinen postaaja Stoney
Provari tasaa pulssit tasavirraksi ja myös säätää lennossa että ulostuleva tasavirta on asetusten mukaista. Lopputulos on kauniin tasaista tasavirtaa. Mittarilla saa ulos samat tiedot kuin esim. akkumodista suoraan. Amppeerit, ohmit, watit, voltit. Toki se on kätevää katsoa mittarista kuinka monta wattia milläkin asetuksella tulee ulos.
Mielestäni ehdottomasti ei. Mittalaitteiden luonnollinen kieli on englanti, ja käännös olisi teennäinen ja vain pienen piirin käytössä. Lisäksi tietojen vertailu tai katselu muiden toimesta menisi hankalaksi, jos otsikot ja lyhenteet olisivat outoja ja tuntemattomia.
+1Lainaus:
Alkuperäinen postaaja overflow
Useiden yritysten jälkeen on todettava, että ZMax mittaus ei minulta onnistunut tällä mittarilla :(. Päätteelle tulostuva tieto on suurelta osin sotkua. Välillä näkee, että odotetun tapaisia lukuja saadaan, mutta useimmiten sotkusta ei saa riittävästi selvää. Vertailun vuoksi, samoilla johdoilla, ProVarin kanssa luvut näkyvät täysin virheettä, ja VMaxin kanssa pieniä satunnaisia virheitä näkyy joskus, mutta harvoin. Ehkä tähän on syynä ZMaxin käyttämä poikkeuksellisen pieni taajuus, 50Hz. Joku muu modi oli myös sadan hertzin luokassa, mutten muista mikä. EVO on sitten luokassa 19kHz, eikä päätteelle tulostu mitään. Tämä on tietenkin mittarin speksit ylittävä taajuus.
Kokeilen tuota vielä myöhemmin sellaisenaan ZMaxin kanssa, ilman päätettä. Ensin kuitenkin mittaan ZMaxin skoopilla ja yleismittareilla, jotta saan tulokset taulukoitua. Ne julkaisen ZMax ketjussa aikanaan.
Onkos toi nyt hyvä vai huono asia Zmaxin kannalta?
https://dl.dropbox.com/u/11701671/E-savuke%20IV/eye.jpg
Lukuja odotellessa :D
Tuota tovin käyttäneenä niin jos tuosta 2.0 joskus tulee niin pari juttua.
Mikrokytkin millä vaihtaa moodien välillä. Reverse polarity jumpperi. Ja kun tuosta ylhäältä luin niin paikka nappipatterille että näyttö on päällä koko ajan.
Ja jos näytöllä olevia tekstejä kerran on helppo vaihtaa niin tuossa pari muutosta jotka olisi kivoja:
bat - bat
cur - amp
res - ohm
por - wat
rns - rns
dut - dut
fre - fre
Mielettömän siisti peli kyllä. Harmittaa maanantaina postittaa takaisin mutta sitten voikin odotella omaa mittaria :P
Harmi kun tuli viivyteltyä nimen lisäämisen kanssa ja jäi välistä. Olis voinu jotain käyttöliittyymää, graafeja ja logeja -ohjelmaa väsäillä. Sarjaportista kuitenki aika helppo olis ollu lukee datat. Noh ehkä viel joku päivä
Donglet tul... Vielä kun saisi ilmotuksen, että itse piirit olisi matkalla :D
https://dl.dropbox.com/u/11701671/E-...0IV/dongle.jpg
(Pussitin uudelleen)
jeejee :)
Näyttää hyvältä. Laitoin eilen tulemaan takaisin lainamittarin. Meni maxikirjeeksi eli myöhästyy ainakin päivän.