Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Jalippo
No nyt alkaa tulla lisää kysymyksiä:
4. Kannattaako lanka polta sytkärillä kerran kaks hehkuvaksi ennen kieputtamista ja mihin se oikein vaikuttaa?
5. Jos haluaa vaihtaa lankaa, niin onko silloin syytä kääriä uusi wick, vai kannattaako hyödyntää vanhaa?
4. uskoisin että tämä vaikuttaa vaan siihen, että vastuslanka on tällöin helpompi käsitellä coilia tehdessä?
5. Riippuu kait ihan siitä wickistä, että miltä se näyttää. Jos se johtaa nestettä vielä hyvin niin en näe kovin suurta syytä vaihtaa wickiä.
Hyvä lukea myös näitä onnistumisia täältä. Mites porukoilla jotka ovat onnistuneet saamaan hyvän wickin ja coilin, toiminnan vertailua esim. kartoihin?
Vs: Meshin käärintää ja vastuslangan virittelyä
Löysin tollasen datasheetin noista Kanthal tyyppien ominaisuuksista ja tässä pieni otos siitä:
http://img269.imageshack.us/img269/4480/kanthal.jpg
Linkit kiinnostaa, jos joku on löytänyt tota parasta APM laatua jostain.
Linkkejä saa laittaa myös A1 laatuun, koska itse en ole törmännyt kuin D laadun lankoihin näissä 0,12 - 0,30 paksuuksissa.
Vs: Meshin käärintää ja vastuslangan virittelyä
Lanka kestää viikon-kaksi, wick kestää kuukausi kaupalla.
Meshin käärintää ja vastuslangan virittelyä
Mites muuten saisiko tuollaisen Genesis-tyylisen aton toimimaan NR-lanka & lämpölanka-kombolla Odysseuksen/Bullin tyyliin?
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Troll from behind
Mites muuten saisiko tuollaisen Genesis-tyylisen aton toimimaan NR-lanka & lämpölanka-kombolla Odysseuksen/Bullin tyyliin?
Niin ja kertokaas nyt vielä tollasen kombon toimintaperiaate.
Toinen lanka on normaalia kanthalia, josta saadaan lämpölanka(?) ja toinen lanka on ? ja ne yhdessä tekee ilmiön x?
Vs: Meshin käärintää ja vastuslangan virittelyä
Genesikseen voi laittaa kyllä lasikuitu wickkin ja siihen coilin ympärille ja esim Orionissa itsellä on ollut dual systeemi jossa toinen tuolla tavalla ja toinen meshillä. Periaatteessa on turhaa laittaa lasikuitua koska silloin juurikin menetetään tuo meshin etu joka on selkeä maku jne. Lasikuitu soveltuu parhaiten vaaka coileihin joissa neste tulee molemmilta puolilta wickkille, pysty ratkaisuissa meshin kapillaari ilmiö on parempi wickkauksen kannalta.
NR lankaa käytetään pelkästään johtimena eli sen tarkoitus on vain siirtää virta coilille, tämän asian hoitaa genesiksessä runko ja johtimet.
Vs: Meshin käärintää ja vastuslangan virittelyä
En oikeestaan ymmärtänyt edellistä, allergialääkkeet tekee vähän kaiken vaikeammaksi.. :D
Pitääpä joskus kokeilla, jos käärisi tuon meshin 'narun' ympärille jota tuli tilattua joskus Peleonilta jokunen metri.. toimiikohan?
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
pki
En oikeestaan ymmärtänyt edellistä, allergialääkkeet tekee vähän kaiken vaikeammaksi.. :D
Pitääpä joskus kokeilla, jos käärisi tuon meshin 'narun' ympärille jota tuli tilattua joskus Peleonilta jokunen metri.. toimiikohan?
Tämä nyt vähän mutuilua omalta kohtaa kun en ole vielä päässyt sukkaa käärimään, mutta eikös toi genesis ota sitä korvaus ilmaa sieltä meshin keskellä olevasta ilmareiästä + muusta ilmareiästä, jolloin se nesteytys paranee? Eli jos meshin tukkii wickillä niin ei välttämättä nesteytys ole niin nopeaa?
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
pki
En oikeestaan ymmärtänyt edellistä, allergialääkkeet tekee vähän kaiken vaikeammaksi.. :D
Pitääpä joskus kokeilla, jos käärisi tuon meshin 'narun' ympärille jota tuli tilattua joskus Peleonilta jokunen metri.. toimiikohan?
Näissä asioissa olen täysin aloittelija, mutta mikäli olen ymmärtänyt oikein niin:
1) Jos haluat käyttää "narua" eli sitä silica wickia, niin upota pelkkä naru tankkiin ja kierrä siihen vastus ympärille
2) Meshin toimintaperiaatteena on ontto rosterisukasta kääritty putki (wick), jolloin alipaine kuljettaa wickin reiästä nestettä ylöspäin vastukselle. Silica lanka tuon wickin sisällä vain huonontaisi tuota toimintaa - dry hittejä.
Nämä DIY atogurut saa korjata aivan vapaasti kaikki mahdolliset virheeni! :D
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Jalippo
Näissä asioissa olen täysin aloittelija, mutta mikäli olen ymmärtänyt oikein niin:
1) Jos haluat käyttää "narua" eli sitä silica wickia, niin upota pelkkä naru tankkiin ja kierrä siihen vastus ympärille
2) Meshin toimintaperiaatteena on ontto rosterisukasta kääritty putki (wick), jolloin alipaine kuljettaa wickin reiästä nestettä ylöspäin vastukselle. Silica lanka tuon wickin sisällä vain huonontaisi tuota toimintaa - dry hittejä.
Nämä DIY atogurut saa korjata aivan vapaasti kaikki mahdolliset virheeni! :D
2) Muistaakseni täältä jostain luin, että jättämällä mm. tankin täyttöruuvin kokonaan pois tuo mesh 'wickaisi' huomattavasti paremmin. En tajunnut tuon meshin keskireiän toimivan kuten kuvasit.
Vs: Meshin käärintää ja vastuslangan virittelyä
Ilmeisesti en ollut hapettanut meshiä kunnolla, kun eilen tehty 4 kierroksen 0.20mm kanthal antoi vastukseksi 1.1ohm genesis minissä?
Tänään kun tuota tökin sormella hiukan niin vastus pomppasi 2.2ohm.
Noh, tutkimusmatka jatkuu... tänään tuli postissa 0.15 ja 0.18 kanthalit.
:antismoke:
Vs: Meshin käärintää ja vastuslangan virittelyä
Milläs ootte kuumentanu meshin? Pikaisella kokeilulla sytkärillä on ainakin aivan turha lähteä leikkimään, räjähtää sytkäri aikaisemmin käteen kun on saanu meshin hehkuvaksi :D
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
esmoke
Milläs ootte kuumentanu meshin? Pikaisella kokeilulla sytkärillä on ainakin aivan turha lähteä leikkimään, räjähtää sytkäri aikaisemmin käteen kun on saanu meshin hehkuvaksi :D
Kaasupoltin tohon hommaan tarvitaan.
Sytkärissä ei riitä lämpö.
Vs: Meshin käärintää ja vastuslangan virittelyä
http://www.dealextreme.com/p/jet-130...e-lighter-1320
http://img.dxcdn.com/productimages/sku_1320_1.jpg
Tuollanen toho ja huoltoasemalta pullo kaasua. Toho ja kaasu ylösalaisin ja rutistus, kaasu valuu sytkään.
Vs: Meshin käärintää ja vastuslangan virittelyä
Huomattavasti kompaktimpi kuin meikän malli. :laugh:
Vs: Meshin käärintää ja vastuslangan virittelyä
Tuli käytyä nopeasti hakemassa töhö nopeasti Biltemasta, näytti ajavan asiansa, ensimmäinen oma setup kääritty :)
Vs: Meshin käärintää ja vastuslangan virittelyä
Nyt tarvis apuja coilin käärimisessä... käytän peleonin 0.12mm lankaa ja vastukset nousee kivasti sinne 2.5ohm mutta... tulee hotspot justiin siihen keskiruuvin ja meshin välille ja palaa poikki lanka
kokeilin myös 0.15mm lankalla ja siinä samassa paikassa hotspot. Yritin hienosäätää coilin kierroksia mutta ei onnistunut. Mistä lähden etsimään vikaa coilista / wickistä?
Mesh sukka on kaasupoltettu 3x molemmista päistä ja tein sen neste + sytkäpolton myös (mitä tuosta muuten on apua?).
Vs: Meshin käärintää ja vastuslangan virittelyä
Täällä oli sama onhelma 0.2 langalla. Pari settiä käärisin kunnes otin meshin kauniiseen käteen ja töhötin vielä kerran kunnolla ja poltin nestettä pari kertaa. Tämän jälkeen hotspotti hävis.
Vs: Meshin käärintää ja vastuslangan virittelyä
juurikin tuollainen hotspot kielii siitä että mesh vetää coilia oikariin. Muutama uusi kuumennus ja yleensä alkaa toimimaan. Tuo nesteellä polttelu vie pois sitä alkuvaiheen metallista makua ja teoriassa helpottaa kapillaari reaktion alkamista eli wickkaa paremmin.
Vs: Meshin käärintää ja vastuslangan virittelyä
http://www.youtube.com/watch?v=Kbypsia9zns
Tohotin runsaasti lisää kaasutoholla ja vieläkin antaa hotspottia tuosta kohtaa mistä menee se lanka tuohon keskipostiin (+-napa?)
Pitää varmaan kokeilla tehdä uusi wick vaikka en kyllä ymmärrää kuinka wickissä voisi olla vikaa... :o