Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
spirit222
Panasonicin CGR18650CH akulla ainakin menee päätycäp täysin kiinni isommalla putkella. Itseltä löytyy pari noita panaa.
http://www.akkula.fi/Panasonic-CGR18650CH-2250-mAh
Myönnetään, että ei se nyt kuitenkaan nätti yhdistelmä oo. On kuitenkin toimivin omista tän hetken atoista mini modin kanssa ja ei näytä tatilta kuin esim. terminator kiinni :D Tuo päädyn halkaisija on 19mm, joten ainakin kaiffari kopio bt804 pitäs istua suoraan hyvin (halkaisija 18.87mm DV:n mukaan).
Juu toi Panasonic on melkeimpä lyhin kaikista 18650-akuista. Mul on myös tuollainen Pana, mut se on Cree Xm-l led taskulamppu käytössä. Maailman lyhkäisin lamppu 18650 akulla ja tolla tehokkaalla uudella ledillä, Panasonic oli ainut joka sinne mahtui.
Noh ei tä pieni rako putkessa tällä Efestillä varmaan kai sit mitään haittaa...
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
Troll from behind
Aikas pitkältä K-57 linjoilla. Automaatio siitä, että halpa on huono ei oikein päde joka putkessa eikä tämä edes ole halvimmasta päästä.
MODin ja eVicin control headit plus putkia on aikas voittajakombo.
Se tuossa tosin taitaa tulla, että reguloidulla saa olla tarkkana sen RBAn ohmien kanssa. Veikkaisin, että alle ohmissa iskee suojat kiinni.
Tulihan sieltä se vastaus reguloidun osalta :) Mahtaakohan suojat päteä reguloimattomana? Jos se virta silti kulkee saman piirin kautta.
Vs: Joyetech Mod 18650/18350
Jännitehävikki on reguloimattomana tässä Efestin 18350 akulla ja 1,5Ohmin vastuksella jotain +0,5V. Tuntuu myös tuo regulointi antautuvan pienemmillä vastuksilla.. :/ Tätä en saa mitattua tankkimittarilla, luultavasti jonkinmoinen pulssi kyseessä. Noaloxia tms tämä huutaa kierteisiin heti alkuun.
Otin tästä 18350 putken eviciin ja lykkäsin evicin putken ja akun tähän, Vivi nova 1,6Ohm setupilla nokkaan ja emännälle käyttöön. Tykkää kyllä. :D
Vs: Joyetech Mod 18650/18350
3. kerta kun toi nappi on jääny pohjaan höyryttelyn aikana. Pieni ihmetyksen tunne kun napista irrottaa ja silti tankin pöhinä jatkuu, napin valo palaa ja höyryä tulee.
Äkkiäkös sen räpläämällä nousemaan taas saa ja jatkettua höyryttelyjä, mut silti vähän laski se laatufiilis ja luotettavuus taas.
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
Natsu
3. kerta kun toi nappi on jääny pohjaan höyryttelyn aikana. Pieni ihmetyksen tunne kun napista irrottaa ja silti tankin pöhinä jatkuu, napin valo palaa ja höyryä tulee.
Äkkiäkös sen räpläämällä nousemaan taas saa ja jatkettua höyryttelyjä, mut silti vähän laski se laatufiilis ja luotettavuus taas.
:o Itelle ei onneksi tuollasta oo sattunut vielä kertaakaan reilun 2.5 viikon omistuksen aikana, joten hyvä laatuvaikutelma on vieläkin kunnossa :D
Asiaan liittyen: Kyllä watti säätöä vaan kaipaa tähänkin, kun tottunut dna box modiin. Tämä ollut nyt yksistään pari päivää töissä mukana ja välillä olis tehnyt mieli laittaa vähän lisää hönkää. Eli kai se pitää laittaa bargain vapoursilta tilaukseen evic head, niin on se watti säätökin kunnossa ja modin koko pysyy sopivana mini modin putkella :D http://www.bargainvapour.com/JoyeTech_eVic_Control_Head_in_stock!/p1274299_8649233.aspx
edit: eVic head tilattu ja oli jopa halvempi mitä peleonilla. Tosin toimituskulut mukaan lukien menee varmaan samaan peleonin kanssa.
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
spirit222
:o Itelle ei onneksi tuollasta oo sattunut vielä kertaakaan reilun 2.5 viikon omistuksen aikana, joten hyvä laatuvaikutelma on vieläkin kunnossa :D
Asiaan liittyen: Kyllä watti säätöä vaan kaipaa tähänkin, kun tottunut dna box modiin. Tämä ollut nyt yksistään pari päivää töissä mukana ja välillä olis tehnyt mieli laittaa vähän lisää hönkää. Eli kai se pitää laittaa bargain vapoursilta tilaukseen evic head, niin on se watti säätökin kunnossa ja modin koko pysyy sopivana mini modin putkella :D http://www.bargainvapour.com/JoyeTech_eVic_Control_Head_in_stock!/p1274299_8649233.aspx
edit: eVic head tilattu ja oli jopa halvempi mitä peleonilla. Tosin toimituskulut mukaan lukien menee varmaan samaan peleonin kanssa.
Höh, just ku tilasin sieltä 2x 100ml ja pari Hyper 4, tankkia. Pähkäilin pitkään et otanko mukaan tilaukseen ton headin, mut visalasku sanoo et ei käy.
Kyl mä tällä näin alkuun koitan pärjäillä näillä normitehoilla, on noita vv-laitteita sit muita tossa. Tätä varten olis tarkotus johonkin tankkiin rakentaa itse joku pienivastus-setuppi tulevaisuudessa ja pelata muutenkin pienillä ohmeilla. Täytyy kärkkyä se evic-headi sit joskus myöhemmin vaikka foorumeilta...
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
spirit222
Asiaan liittyen: Kyllä watti säätöä vaan kaipaa tähänkin, kun tottunut dna box modiin. Tämä ollut nyt yksistään pari päivää töissä mukana ja välillä olis tehnyt mieli laittaa vähän lisää hönkää. Eli kai se pitää laittaa bargain vapoursilta tilaukseen evic head, niin on se watti säätökin kunnossa ja modin koko pysyy sopivana mini modin putkella :D http://www.bargainvapour.com/JoyeTech_eVic_Control_Head_in_stock!/p1274299_8649233.aspx
edit: eVic head tilattu ja oli jopa halvempi mitä peleonilla. Tosin toimituskulut mukaan lukien menee varmaan samaan peleonin kanssa.
Tuossahan Evicin contorl Hedissä hän ei tule usbi piuhaa mukana. Millainen sen pitäis olla?? Ajattelin kans itse tilata tuon Evicin hedin.
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
pdz4
Tuossahan Evicin contorl Hedissä hän ei tule usbi piuhaa mukana. Millainen sen pitäis olla?? Ajattelin kans itse tilata tuon Evicin hedin.
Googlen mukaan micro usb ja noita ainakin itellä pyörii jo nurkat täynnä, kun tullut kännyköiden ja digikameroiden mukana.
Vs: Joyetech Mod 18650/18350
Saapu tänään postissa AGA-T+ ja pitihän sitä heti kokeilla joeymodilla tehdä hapettamaton mesh setuppi. Reguloimaton moodi päällä pulssia antamaan ja hyvin meni about 2min ja sain jo 1,5 kieppiä hehkumaan niinkuin pitää. Kuitenkin parin minsan jälkeen modin valot alkoi vilkkumaan ja ei anna tulittaa enää. Ei auta akun vaihto tai mikään eli rikki meni :-\
Eli kaikille tiedoksi, että joyetech modi ei kestä tuollaista rääkkiä kuten hapettamattoman mesh setupin teko. Onneksi varaosat on halpoja ja evic head on tulossa, niin ei jää nuo akkuputket käyttämättä. Eikai tässä auta, kuin alata ettimään mekaanista modia tuollasta rääkkiä varten :esmoke:
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
spirit222
Saapu tänään postissa AGA-T+ ja pitihän sitä heti kokeilla joeymodilla tehdä hapettamaton mesh setuppi. Reguloimaton moodi päällä pulssia antamaan ja hyvin meni about 2min ja sain jo 1,5 kieppiä hehkumaan niinkuin pitää. Kuitenkin parin minsan jälkeen modin valot alkoi vilkkumaan ja ei anna tulittaa enää. Ei auta akun vaihto tai mikään eli rikki meni :-\
Eli kaikille tiedoksi, että joyetech modi ei kestä tuollaista rääkkiä kuten hapettamattoman mesh setupin teko. Onneksi varaosat on halpoja ja evic head on tulossa, niin ei jää nuo akkuputket käyttämättä. Eikai tässä auta, kuin alata ettimään mekaanista modia tuollasta rääkkiä varten :esmoke:
Mitään hapettamattomista tietävänä täytyy kysyä, et onko toi hapettamaton jotenkin raskaampi setuppi modille käsitellä? Pitäis koht Phoenix Picoon tehdä ihan normi esikois mesh-setuppi ja kokeilla sitä joyemodin kanssa.
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
Natsu
Mitään hapettamattomista tietävänä täytyy kysyä, et onko toi hapettamaton jotenkin raskaampi setuppi modille käsitellä? Pitäis koht Phoenix Picoon tehdä ihan normi esikois mesh-setuppi ja kokeilla sitä joyemodin kanssa.
Hapettamattoman meshin teko on raskasta modille ja akulle, koska se on oikosulussa kunnes vastuslanka on hapettanut meshin. Eli tolla tyylillä setuppia tehdessä vastuslanka toimii "tohona" ja hapettaa langan alla olevan meshin. Amppeerit nousee sen verta korkealle, että oman joyemodin elektroniikasta jotain kärvähti. Valmiit mesh setupit kyllä toimii täysin joyemodissa, mutta tuo setupin valmistelu hapettamattomalla tyylillä on sille liikaa (normi tohotus ja nestepoltto tyyli toimii kyllä). Eli valmisteluun hapettamattomalla tyylillä olis paras joku täysin mekaaninen modi.
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
spirit222
Hapettamattoman meshin teko on raskasta modille ja akulle, koska se on oikosulussa kunnes vastuslanka on hapettanut meshin. Eli tolla tyylillä setuppia tehdessä vastuslanka toimii "tohona" ja hapettaa langan alla olevan meshin. Amppeerit nousee sen verta korkealle, että oman joyemodin elektroniikasta jotain kärvähti. Valmiit mesh setupit kyllä toimii täysin joyemodissa, mutta tuo setupin valmistelu hapettamattomalla tyylillä on sille liikaa (normi tohotus ja nestepoltto tyyli toimii kyllä). Eli valmisteluun hapettamattomalla tyylillä olis paras joku täysin mekaaninen modi.
Ei kuulosta hirveen turvalliselta touhulta jos oikosulussa mennään :D Montakohan oikosulkua akku kestää kunnes elinikä on loppu? Vai onko tää hapettamaton mesh ihan hyväksi todettu asia?
Vs: Joyetech Mod 18650/18350
Hyvin se pelittää täysmekaanisella putkella; vastuslanka palaa poikki ennen kuin akulle käy mitään jos liian kauan antaa virtaa. ;)
Ensimmäistäkään akkua en ole saanut rikottua, eikä kapasiteetissakaan näytä mitään eroa olevan, vaikka yhdelläkin akulla olen tainnut 7 wickiä hapettaa (ilman latausta välissä siis) kun tuli tutuille pidettyä "koulutusta" tohottamattoman meshin käyttöönotossa. ;)
Tohottamaton (siis vastuslangan avulla hapetettu) meshi on kyllä hyväksi todettu ja nopea keino saada setuppi pelittämään kunnolla. Viimeisin kokeilu SDogiin litteällä vastuslangalla otti ~20 sek. hehkuttelua saada setuppi toimimaan oikein. 8) Ei ihan samoihin pääse tohon kanssa leikkimällä. :D
Edit. Mainitaan nyt vielä sen verran, että mekaanisen akkuputken kanssa näissä hommissa on sitten syytä käyttää suojaamattomia turvakemia-akkuja (=IMR tai vastaava), jottei suojapiiri puhalla peliä liian aikaisin poikki ja ettei vahingossakaan akku poksahda. ;)
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
Charun
Hyvin se pelittää täysmekaanisella putkella; vastuslanka palaa poikki ennen kuin akulle käy mitään jos liian kauan antaa virtaa. ;)
Ensimmäistäkään akkua en ole saanut rikottua, eikä kapasiteetissakaan näytä mitään eroa olevan, vaikka yhdelläkin akulla olen tainnut 7 wickiä hapettaa (ilman latausta välissä siis) kun tuli tutuille pidettyä "koulutusta" tohottamattoman meshin käyttöönotossa. ;)
Tohottamaton (siis vastuslangan avulla hapetettu) meshi on kyllä hyväksi todettu ja nopea keino saada setuppi pelittämään kunnolla. Viimeisin kokeilu SDogiin litteällä vastuslangalla otti ~20 sek. hehkuttelua saada setuppi toimimaan oikein. 8) Ei ihan samoihin pääse tohon kanssa leikkimällä. :D
Edit. Mainitaan nyt vielä sen verran, että mekaanisen akkuputken kanssa näissä hommissa on sitten syytä käyttää suojaamattomia turvakemia-akkuja (=IMR tai vastaava), jottei suojapiiri puhalla peliä liian aikaisin poikki ja ettei vahingossakaan akku poksahda. ;)
Kiitti taas Charun kattavista neuvoista. Tarviiko tällaisiin setuppeihin atotankissa olla eristetty mesh-reikä? Eikä nestepolttoa tarvitse ollenkaan? Mul olis tossa Phoenix Pico odottamassa mut ei kiinnostais toholeikit. Onnistuuko tolla? Täysin mekaanisia putkia löytyy pari kappaletta.
Vs: Joyetech Mod 18650/18350
Ei vaadi eristettyä meshireikää, ottaa vaan yleensä pikkasen kauemmin se hapetus ja saattaa herkemmin polttaa vastuslangan poikki, mutta kun hyvin lyhyillä pulsseilla antaa alkuun virtaa, niin saa senkin kyllä tehtyä.. Ensimmäistä kertaa kun kokeilin eristämättömään reikään tehdä tohottamattoman setupin Arrowiin niin vain kerran kärähti lanka poikki. :D
Nestepolttoakaan ei kuulu tehdä, jos hapetus tehdään vastuksella. Pieni "sisäänajo" saattaa olla tarpeen, että alkaa wickaamaan riittävästi; SDogin viimeisimmällä setupilla (#500 meshistä umpinanen wicki) meni ~0.5-1ml että wickaus alko kunnolla pelittämään, mutta välillä taas wickaa heti alusta asti oikein (henkimaailman juttuja joihin luultavasti myös tähtien asento ja kuun kierto vaikuttaa).. :P
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
Charun
Ei vaadi eristettyä meshireikää, ottaa vaan yleensä pikkasen kauemmin se hapetus ja saattaa herkemmin polttaa vastuslangan poikki, mutta kun hyvin lyhyillä pulsseilla antaa alkuun virtaa, niin saa senkin kyllä tehtyä.. Ensimmäistä kertaa kun kokeilin eristämättömään reikään tehdä tohottamattoman setupin Arrowiin niin vain kerran kärähti lanka poikki. :D
Nestepolttoakaan ei kuulu tehdä, jos hapetus tehdään vastuksella. Pieni "sisäänajo" saattaa olla tarpeen, että alkaa wickaamaan riittävästi; SDogin viimeisimmällä setupilla (#500 meshistä umpinanen wicki) meni ~0.5-1ml että wickaus alko kunnolla pelittämään, mutta välillä taas wickaa heti alusta asti oikein (henkimaailman juttuja joihin luultavasti myös tähtien asento ja kuun kierto vaikuttaa).. :P
Kiitos kiitos.
Unohtui viel kysyä et ajellaanko tämä setuppi käyttökuntoon ilman nesteitä vai nesteiden kanssa?
Vs: Joyetech Mod 18650/18350
Kun oot saanu hapetettua setupin kuntoon (eli kaikki kiepit hohkaa tasasesti ja hehkuminen etenee keskeltä laitoja kohti), niin nesteet vaan sisään ja höyryämään. ;)
Saattaa alkuun vaatia hieman lyhyempiä vetoja tai laitteen kallistelua, jos ei wickaa kunnolla, mutta tosiaan pienen käytön jälkeen yleensä lähtee wickauskin toimimaan. :)
Tällä viikolla luultavasti tekasen pikasen videokatsauksen Somnium V2:een ja samalla väännän tohottamattoman setupin; katsotaan, jos siitä jonkunlaisen tutoriaalin sais samalla aikaseks, vaikka melko yksinkertanen operaatio tuo kokonaisuudessaan on. ;)
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
Charun
Kun oot saanu hapetettua setupin kuntoon (eli kaikki kiepit hohkaa tasasesti ja hehkuminen etenee keskeltä laitoja kohti), niin nesteet vaan sisään ja höyryämään. ;)
Saattaa alkuun vaatia hieman lyhyempiä vetoja tai laitteen kallistelua, jos ei wickaa kunnolla, mutta tosiaan pienen käytön jälkeen yleensä lähtee wickauskin toimimaan. :)
Tällä viikolla luultavasti tekasen pikasen videokatsauksen Somnium V2:een ja samalla väännän tohottamattoman setupin; katsotaan, jos siitä jonkunlaisen tutoriaalin sais samalla aikaseks, vaikka melko yksinkertanen operaatio tuo kokonaisuudessaan on. ;)
Hyvä hyvä!
Katselen sellaisen videon mielelläni :)
Vs: Joyetech Mod 18650/18350
Juu-u, niin ne asiat kehittyy. Itsekkin heitin perjantaina ekan tohottoman setupin. Pico (eli eristämätön wick-reikä) ja hyvin workkii, jopa paremmin kun tohotettu ja nestepoltettu. Hommatkaa sitä awg-28 kantahalia, olisko ollut 50feet 12 dollaria posteineen. Ja taitaa olla jopa parasta A1-luokkaa. Ei ole kertaakaan palanut poikki, 4 kieppiä picossa on 0.8 ohmia ollut kerta toisensa jälkeen. Paksuus siis 0.32mm tuolla langalla.
Sitten takaisin aiheeseen, en muutenkaan suosittele käyttämään mesh-setuppia tälläisten ego-tyylisten laitteiden kanssa. Kaksi egon akkua mennyt roskiin näiden takia. Toinen toimi hetken hyvin ja sitten simahti. Koitin mekaanisella, niin oli lanka päässyt vetämään oikkarin ihan itsellään vaikka oli aiemmin toiminut hyvin.
edittiä, kiitos Esmokelle
Vs: Joyetech Mod 18650/18350
Lainaus:
Alkuperäinen postaaja
muti88
Juu-u, niin ne asiat kehittyy. Itsekkin heitin perjantaina ekan tohottoman setupin. Pico (eli eristämätön wick-reikä) ja hyvin workkii, jopa paremmin kun tohotettu ja nestepoltettu. Hommatkaa sitä awg-36 kantahalia, olisko ollut 50feet 12 dollaria posteineen. Ja taitaa olla jopa parasta A1-luokkaa. Ei ole kertaakaan palanut poikki, 4 kieppiä picossa on 0.8 ohmia ollut kerta toisensa jälkeen. Paksuus siis 0.3mm tuolla langalla.
Sitten takaisin aiheeseen, en muutenkaan suosittele käyttämään mesh-setuppia tälläisten ego-tyylisten laitteiden kanssa. Kaksi egon akkua mennyt roskiin näiden takia. Toinen toimi hetken hyvin ja sitten simahti. Koitin mekaanisella, niin oli lanka päässyt vetämään oikkarin ihan itsellään vaikka oli aiemmin toiminut hyvin.
Eikai nyt kuitenkaan AWG 36? 4 kieppiä 0.8ohmia kuulostaa AWG28:lta, eli 0.32mm langalta.