Kylläpäs jenkit ryssii noita vaihtoja. Toivottavasti ei paljastu uutta bigdogia.
Printable View
Kylläpäs jenkit ryssii noita vaihtoja. Toivottavasti ei paljastu uutta bigdogia.
Alkaa olla jo vasaralla kokoa 8)
https://dl.dropbox.com/u/11896363/WP_000123a.jpg
https://dl.dropbox.com/u/11896363/WP_0001211.jpg
Nyt kaivattas neuvoja miten saada kaks kierteillä varustettua rst-palasta irti toisistaan. Caravelan topcap ja kayfunin bottomcap on jumiutunu niin helvetin kovaa toisiinsa kiinni, että en tahdo millään saada irti. On kuumennettu, pakastettu, väännetty ja käännetty ja ei inahdakkaan mihinkään suuntaan. Väärille kierteille ne ei ole menny, mutta jostain helvetin syystä ne on todella tiukassa. Sormet jo aivan verillä. Pihtejä en haluais käyttää, koska tartuntapinta-alaa ei ole oikein muuten kuin kierteiden kohdalta ja paskaksihan ne menee. Ideoita?
Vaikka sanoitkin ettet halua pihtejä käyttää niin samanlaisen kombon sain auki niin et laitoin 22mm tai jotain paksua kumiputkea ympärille ja jeesuksenleuoilla väänsin auki. Eikä tullut naarmuja.Lainaus:
Alkuperäinen postaaja vanttila
Ota se caravelan yläcäppi irti ja koita pohjasta vääntää pihdeillä sitä säädettävää plusnapaa löysemmälle, jos sit aukeis?
Mulla sama juttu kerran, jyrsimen kanssa juutus holkki niin maan perusteelisesti jumiin, kaverilta sain Motonetista ostettua kylmä spray:tä pulttien aukaisuun, kyllä lähtee/ tai lähti
http://www.amazon.com/PERFORMIX-PLAS.../dp/B000HE9T6A
Vastaavaa löytynee honkkarista tms myös....
Ite oon saanu auki aina kaikki ongelmatapaukset kumihanskoilla. Sellaset missä on runsaasti "grippiä" ja sit vaan painaa osia lujasti yhteen ja vääntää. Ite kans luulin jo saaneeni muutamat hybridit telineeseen, mut noin helpolla konstilla on irronnu.
Caran plussa on otettu pois ja kayfunin plussaa liikuteltu vähän joka suuntaan, eikä mithään.
Pitänee kokeilla vääntää pihdeillä, mutta näköjään tästä huushollista ei löydy tarpeeksi avautuvia pihtejä. Jokatapauksessa piti huomenna käydä ostaan leatherman, onpahan nyt ihan oikee syykin.
Aina kannattas tulla tänne nillittämään kun on joku ongelma. Sain just äsken aukastua sen, vaikka en edes yrittäny. Oon viikon vääntäny täysiä sitä varmaan tunnin päivässä, nyt vähän leikin sillä samalla kun kattelin leffaa ja sehän aukes heti. Voi olla että mulla on vaan niin käsittämättömän isot ja massiiviset voimat, että oon puristanu sitä ihan huomaamattani vahingossa kasaan koko metallipalaa ja sen takia ei oo auennu ::)
Tais olla 30 yhteensä, joista about 1/3 pikkuvasaroita.
Minulle kävi ihan samoin ja myös naama punaisena vääntelin, taisin kerran purkaa myös :) Sitten huomasin ettei siihen kannata käyttää voimaa ollenkaan ja aina sain kahdella sormen otteella auki :) Mietin asiaa ja en keksinyt muutakuin, ovat niin perkeleen hyvin tehtyjä jotta istuvat todella hyvin yhteen. Pienikin voimankäyttö sai osat vielä enemmän yhteen(vääntö). En tiedä oliko päätelmät oikeat, mutta minulla se ainakin toimi :D
IsoD tuli tänään Jalipolta. Onhan se aivan yhtä ihana kuin ennenkin. Valitettavasti vaan tulee ehkä näkemään yhtä vähän käyttöä kuin ennenkin..
Nykyään kun noita drippiatoja lähes pelkästään käytän, niin sain päähäni ajatuksen että nyt on pakko saada darwin taas takaisin. Ongelmahan on vaan siinä, että teen noin 0.8-1.0 ohmisia setuppeja noihin ja ajelen ihan pelkällä akulla. Tuossahan watit nousee jo 16W pintaan. Darwinin 12.7W ja 3.3V alkaa tuntua jo vähän vilposelta.
Pitänee hetki kuitenkin antaa aikaa, sillä onhan tuo aivan ihana laite. Pakko sille on joku käyttötarkotus tästä huushollista löytyä.
Se kävi heti ekana mielessä. Siinä on vaan se huono puoli, et darwin on kuitenkin kotilaite ja pikkunen tankki on kotikäyttöön aika turha.
http://www.youtube.com/watch?v=_6refnsGhxY
Juggernautista videota. Mahtavaa että tää vihdoin näkee päivänvalon kohta. Ehkä se eniten odottami hybridi ikinä, seurannu projektia siitä asti kun ekat kuvat tuli julki. Aivan varmasti menee ostoskoriin.