Kyllähän ne terävältä tuntuu kun Smok Woo joka on kiinteä 5V laite antaa tehollisesti 5.85V. Mittailin tuolla ECD-mittarilla.
Printable View
Öööääää..... Nyt en tiiä mitä tuohon sanoisi. Tai siis missasin pointin.
Ylös ja alas ad Infintum. Mitä laiskempi duty, sen pahemmin sen tuntee. Itselläni kyrvähti WOOlla muutama 3,5 ohminen Io6.
Niiiiiiiin, mutta pienemmilläkin tehoilla tuntuu... noh, terävältä ja ohuelta höyryt.
Onko Zmaxin omistajilla ollut jo ongelmia napin kanssa? Saatta katketa kesken imun tahi välillä saa painaa 2-4 sekkaa ennen ku alkaa pörisee...
Juu sillon tällön, huomasin saman ku Trolli, eli paremmin rokkaa 18650 ku 2x18350 akuilla :)
Itsellä tullut ton napin kanssa samaa, kuin aikoinaan Provarilla, eli näppäilevä höyryttely voikin heittää epähuomiossa valikkoon.
Sitä nappia voi puhaltaa, itse en ihan vähällä lähtisi suihkuttamaan elektroniikanpuhdistinta.
Sori, oli pakko :police:, siis "tehon keskiarvo" käsite olisi oikeammin jännitteen tehollisarvo. Ei muuten, mutta jos joku ryhtyy laskemaan keskiarvoa tehosta... Muutkin kuin kiinalaiset, jotka tosin laskevat keskiarvoa jännitteestä, kun tulisi laskea jännitteen tehollisarvoa. Ei tämä kauhean tarkkaa tietysti ole, mutta aika tarkkaa kuitenkin. :P
Minustakin tuntui heijastinmodin hetkinä, että höyry on jotenkin kulmikkaampaa. Erityisesti pienillä taajuuksilla ero tuntui olevan selkeä, mutta muistaakseni ei kuitenkaan aina. Nyt en ole vertailevaa tutkimusta viitsinyt tehdä, koska sitä varten pitäisi olla testiä helpottava kytkentärasia, valintakytkin jolla voi helposti ja nopeasti valita kumman modin energiaa höyrytykseen käytetään.
Tuosta tulikin lievänä off-topiccina mieleen, että rasian voisi tehdä 3xAA kokoon siten, että valinnan suorittaisi prosessori. Se voisi ensin arpoa satunnaisen vaikkapa 10 hatsin sarjan, ja sen jälkeen feteillä ohjata käyttöön modin A tai B, arvotun mukaisesti. Höyrytys tapahtuisi kun molemmilta modeilta tulee jännitettä. Lopuksi napin painalluksella laite voisi ledeillä ilmaista mikä oli arvottu sarja: A, B, B, A, A jne... Tällöin testi olisi todellinen sokkotesti :).
Ulkomaalaiset vainoo....
Eli oliko testissä käytetty akku suojaamaton AW?
Ilmeisesti noi kaikki muut olivat singlecoileja pl toi 1.5?
Osaakos Guru arvioida, että olisiko perusteltua odottaa tehon suhteen heilahduksia meshillä tai silicalla?
AW IMR akuista ylivuoto puhui ja tosiaan vain tuo 1,5 ohmin tehomittaus 8 watilla tehtiin dual coililla ja muut single coililla. Tai single coilia simuloivalla tehovastuksella. Näin ainakin ylivuodon tekstistä ymmärsin.
Siihen en kyllä usko että modin tehot muuttuisi sen mukaan, minkä materiaalin ympärille coili on kieputettu? Esim. Silica vs. Mesh. ???
Akut siis AW IMR, ja ladattu täyteen ennen jokaista mittaussarjaa. Kuormat ovat tehovastuksia kaikki, koska carton resistanssi ei ole tarkka ja lisäksi vaihtelee hieman. Dual coil on mainittu "tuttuna terminä", mutta myös 1.5 kuormat olivat tehovastus.
Tehon heilahdukseen en osaa perusteellisesti vastata, koska en hoksaa mitä kysymyksellä ajetaan takaa.. Vastusarvon muuttuminen aiheuttaa muutosta mitattavassa tehossa, jos VW ei toimi hyvin, mutta tästä ei taida olla kysymys? Mesh rakenteessa taasen on massaa enemmän, jolloin lämpöteho käyttäytyy hieman eri tavalla, mutta mutta... Ehkä jokin johdanto tai tarkennus kysymykseen olisi paikallaan ;).
Eipä tuossa oikein ole mitään oleellista muuttujaa tehollisesti, luulisi tehon käyttäytyvän samalla tavalla oli se vastus kasattu sitten vanun tai meshin ympärille.
Ainut ero taitaa tulla maussa, th:ssa ja höyryissä, tehollisia vaikutuksia tuskin näkyy.
Onhan tässä se ero, että wickissä se vastus on materiaalin ympärillä, kun taas kartossa se vastus on materiaalin sisällä, näin loogisesti ajatellen täten karto pystyy kosteuttamaan vastusta paremmin = kestää enemmän lämpöä vaikka vastus on sama. Vai feilaako tuo logiikka?
Perstuntumalta kyllä väittäsin, että silicawickiset rebuildablet kestää kyllä selkeesti enemmän tehoja kuin esim. Boget ja meshilliset vielä enemmän.
Olettaen siis että nesteensyöttö pelittää kunnolla; muuten kyllä puskee dry hittiä, kuten myös kuivalla cartolla. ;)
Kestävyydessä voi tosiaan olla heittoja, mutta se, mitä mä hain takaa liittyy juurikin tehoon.
Eli pähkinänkuoressa:
Onko meshissä tai silicassa jotain ominaisuuksia, joiden johdosta lyhyellä tai pitkällä aikavälillä ilmenisi muuttujia, joiden johdosta samalle vastukselle annettu sama jännite johtaisi erisuuruiseen tehoon?
En kyllä näe moista mahdollisuutta oikein mitenkään, etenkään VW-laitteella. Kait tuossa voisi teoriassa meshin kanssa tulla jotain vastuksen marginaalista sahaamista, mutta sen vaikutus kokonaisuudessaan taitaa jäädä olemattomaksi ellei pienemmäksi.
Kaikki laitteet karstoittuu ja coili ei silloin enää hehku niin kuumana samalla teholla. Siis siltä pinnalta joka koskettaa nesteeseen.
Turun miitissä tätäkin pyöriteltiin, sellainen olis mielenkiintoinen modi jossa säädettäisiin vastuslangan kuumuutta wattien tai volttien sijaan. :)