Vs: Meshin käärintää ja vastuslangan virittelyä
Meshin eristykseen löytyi motonetista (perhonsidonta puolelta) erikokoisia siliconi putkia, jotka on ohuella seinämällä.
Testailen tällä hetkellä Severus V2 ja hyvin toimii...
Tosin ei kestä niin hyvin lämpöä kuin ptfe mut laittaa kauemmaksi vastuslangasta ettei käryä
54-8192 1M 3.8x3mm 1.50€
Vs: Meshin käärintää ja vastuslangan virittelyä
Voisko joku valaista että mitä tää meshin kynttiläpoltto tarkottaa?
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Ortep
Voisko joku valaista että mitä tää meshin kynttiläpoltto tarkottaa?
Mesh pötkö pystyyn johonkin metallisen tapin päähän esim.nastaan tai vastaavaan. Sit tiputellaan nestettä meshin päähän että koko mesh on märkä (osa nesteistä valuu pöydälle). Sit eikun sytkärillä neste palamaan
Vs: Meshin käärintää ja vastuslangan virittelyä
Ah, aivan ja tällä voi korvata tohotuksen?
Vs: Meshin käärintää ja vastuslangan virittelyä
kyllä tuolla tavoin saa meshin hehkumaan, tosin riippuu miten paksua nestettä on. Litku neste valuu meshin läpi aika herkästi ja paloaika on luonnollisesti lyhyempi
mut ihan toimiva kikka jos ei tohoa omista
Vs: Meshin käärintää ja vastuslangan virittelyä
kiitosta, tuli tilattua joku did kopio ekaks meshi kokeiluvehkeeks niin piti vaan varmistella kun ei viittis tohoa ostaa jos ei ookkaan se oma juttu
Vs: Meshin käärintää ja vastuslangan virittelyä
Mikähän mahtaa olla hyvästä pois höyry maistuu palaneelle, ohmit provarin näytön mukaan 1.9, sama palaneenkäry antoi virtaa 3.5 tai 5.0 volttia tai jotain siltä väliltä, ei auta sekään vaikka meshin kostuttaa reippaasti pullosta tiputtamalla, voisko syy olla nesteessä?
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Niko
Mikähän mahtaa olla hyvästä pois höyry maistuu palaneelle, ohmit provarin näytön mukaan 1.9, sama palaneenkäry antoi virtaa 3.5 tai 5.0 volttia tai jotain siltä väliltä, ei auta sekään vaikka meshin kostuttaa reippaasti pullosta tiputtamalla, voisko syy olla nesteessä?
Teeppä alusta asti homma uusiksi. Ottaa hotspottia tod. näk. huonosti hapetetun meshin takia.
Vs: Meshin käärintää ja vastuslangan virittelyä
Katso setupin teon jälkeen ensin kuivapoltolla, että kaikki langat hehkuvat ja nesteen täytön jälkeen, ettei hehkua näy missään. Jos edelleen hehkuu, niin vastuslanka on liian löysällä vaikka mesh olisikin kostea.
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Niko
Mikähän mahtaa olla hyvästä pois höyry maistuu palaneelle, ohmit provarin näytön mukaan 1.9, sama palaneenkäry antoi virtaa 3.5 tai 5.0 volttia tai jotain siltä väliltä, ei auta sekään vaikka meshin kostuttaa reippaasti pullosta tiputtamalla, voisko syy olla nesteessä?
Ei wickaa tarpeeksi?
Itelläni oli sama vika DID kopiossa tein uuden meshin vähä paksumman tangon ja nyt tpomii koska wickaa paremmin.
Mutta kenties tuo hotspot on vahvempi veikkaus ja kokeilu kannattaa ettei tankoa tartte uusiks väsätä.
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Rotax
Katso setupin teon jälkeen ensin kuivapoltolla, että kaikki langat hehkuvat ja nesteen täytön jälkeen, ettei hehkua näy missään. Jos edelleen hehkuu, niin vastuslanka on liian löysällä vaikka mesh olisikin kostea.
Liian löysissä langoissa vika varmaan onkin, joiltakin kohdin hehkuu kosteanakin.
Minäpä väsään uudelleen koko setupin.
Kiitos neuvoista jokaiselle.
Vs: Meshin käärintää ja vastuslangan virittelyä
^Itse ainakin koen helpompana pyöritellä coili paikoilleen ennen meshin paikoilleen laittamista. Tällöin kireys on sopiva. Pikkusen löysää, ennen keskitolppaan laitoa ylimmästä kiepistä, niin jää se yleisin hotspot pois. Coilin hehkuessa tökit läpi, katsot että hehkuu alkaen keskeltä päihin ja sitten annat muutamat kunnon kuivapoltot ja ei muuta kun höyryä perään.
Vs: Meshin käärintää ja vastuslangan virittelyä
Lainaus:
Alkuperäinen postaaja
Verska
^Itse ainakin koen helpompana pyöritellä coili paikoilleen ennen meshin paikoilleen laittamista.
Taidanpa muuten tehdä samoin, höylän kutterissa tuunatut sormet on kuin nippu kyrpiä joilla ei kunnon otetta ja tuntumaa saa pieniin osiin.
Vs: Meshin käärintää ja vastuslangan virittelyä
Toistan edelleen vinkkinä sitä, että käärinnässä kannattaa pyörittää laitetta eikä lankaa. Juuri äsken ZAP:iin tehty eristämätön setupppi toimi ekalla :D
Vs: Meshin käärintää ja vastuslangan virittelyä
Löysin ketjun noista meshin polttoon tarkoitetuista kaasupolttimista, multahan puuttuu tarpeeksi tehokas poltin jolla meshin polttaa, vaikka tuossa sikaritohossa kuuma sininen liekki onkin se on aivan liian pieni ja tehoton meshille.
Eipä mikään ihme etten saa toimimaan kunnolla kun puuttuu kunnolliset välineet.
Vs: Meshin käärintää ja vastuslangan virittelyä
Tohon puutteeseen tepsii kynttiläpoltto, eli kastele meshi nesteellä ja pidä sitä pystysuorassa esimerkiksi pihdeillä ja sytytä yläpäästä. Toistoja 4-5 kertaa niin kyllä hapettuu. Kriittisin kohtahan on se, mihin vastuslanka tulee kiinni (ja jos ei ole eristystä mesh-aukossa niin sekin).
Vs: Meshin käärintää ja vastuslangan virittelyä
^Itse laitan meshin nastan nokkaan niin helppo siinä poltella.
Vs: Meshin käärintää ja vastuslangan virittelyä
Coilin kuivapoltollakin saa meshin punahehkuseksi, jolloin varmasti rokkaa. Itse vedän toho, nestepoltto ja kuivapoltto.
Vs: Meshin käärintää ja vastuslangan virittelyä
Sellaisen vinkin sain muuten noihin halpisluokan genesiksiin, että jättää suosiolla täyttöaukon ruuvin pois jonka jälkeen wickaa. Lisäksi kannattaa käyttää 0.25 kanthalia, jolla saa yhdistelmän alhaiset ohmit (1.6-1.7) sekä runsaasti kierroksia coiliin = runsaasti höyryä.
Vs: Meshin käärintää ja vastuslangan virittelyä
Pitihän se perkeles koittaa vääntää Severukseen 0,3mm Kanthalista setuppi, 0,5-0,6 ohmia, 4/5 kierrosta, mutta en saanu kirveelläkään kierrettyä sitä fiksusti, on sen verran paksua tavaraa. Tarpeeksi ku runnoin sain ottamaan maihin meshiin ja napsahti lanka poikki. Käärin siis vanhan 0,25 kanthalin takasi, 3 kieppiä ja 1,1 ohmia. Ajaa asiansa. Ois ollu miehekäs kyllä tuo setuppi...