Jos ymmärsin oikein, niin sen on tarkoituskin ottaa kiinni mesh-reiän seinämään. Se hapetus estää sitä vain menemästä oikoseen siitä.
Printable View
Jos ymmärsin oikein, niin sen on tarkoituskin ottaa kiinni mesh-reiän seinämään. Se hapetus estää sitä vain menemästä oikoseen siitä.
Liian paksua nimenomaan. Mutta voi ohuestaki pötköstä hapetus hajota ja lyödä maihin aton runkoon. (:Lainaus:
Alkuperäinen postaaja rossian
Kaikkien lenkkien pitäis levätä meshillä sopivalla kireydellä, mutta ylälenkki on kyllä itellä se joka usein on liian tiukalla tai löysällä.Lainaus:
Alkuperäinen postaaja rossian
Viljelen näitä videoitani aina joka paikkaan, mutta minkäs narsisti itselleen mahtaa. Tässä siis Somniumiin setupin teko, josta näette kuinka itse väkerrän hyvän meshin ja miten coili tehdään.
http://youtu.be/UumkccTQWqE
Pääsi siinä videota tehdessä "oho" käymään, siitä ei lannistuta :D
PS. Jalippon video paljon parempi, mutta näettepä että kyllä noobie tähän pystyy myös. Käytössä 0.25mm kanthal jos ei videosta selviä.
haittaako jos coil ottaa runkoon kiinni? haittaako jos coilin kierteet ottaa toisiinsa kiinni?
Runko toimii miinuksena, eli riippuu mistä kohtaa se osuu. Ja ei olisi ihan välttämättä suotavaa että kierrokset osuu toisiinsa, silloin virta hyppää siitä kohdasta ja jättää osan coilista kylmäksi ja vähentää vastusta.Lainaus:
Alkuperäinen postaaja Kurko
Korjatkaa jos valehtelin. :D
Kierrän sen vastapäivään, niin ettei se kiristy kun kiristän mutterin.Lainaus:
Alkuperäinen postaaja rossian
Edit. Eli +postin oikealta puolelta. :D
http://www.finnvape.com/product/260/...astuslanka-20m onko tällä ja a1 kanthalilla paljonki eroa?
HEI!
Suurkiitokset ohjeista.. Käy ja kukkuu.. 500mesh ja .25 kanthal. Maistuu kuminalle taivaalliselta.
Eipä tossa muuta eroa oikeen pitäis olla kun et palaa poikki helpommin. Eli jos tulee hotspottia niin menee kyl katki aika nopeesti. Silica vehkeessä ei niin merkitystä, mut meshi vehkeissä aika helposti tuppaa noita hotspotteja tulemaan.
Aivan, kiitos :)
Tein tossa vision eternityyn uuden 2ohm setupin 2mm silicasta ja .16 nichromesta. 3.2 voltilla (oikeesti) pieni kuivapoltto ja 2 cm korkee kynttilän liekki oli valmis :D onko kellään vastaavia kokemuksia? silican ei käsittääkseni pitäs hirveen helposti syttyä?
Ei se silica mihinkään pala, vaan "varastorasvat" siitä pinnasta, tai sitten sulle on myyty jotain ihan muuta narua. :D
Muun muassa tän takia silicakin on hyvä polttaa etukäteen toholla. Lähtee ylimääräset paskat ja mahdolliset maut. Mulla ei ole ikinä tohottamatonkaan silica syttynyt, mutta se ei ole ennenkuulumatonta.
Niin ja tarkennuksena, kuten Charunkin sanoi, silica ei pala vaan ne mahdolliset töhnät siinä pinnassa.
Jeppps tein perään uuden samoista tarpeista ja kuivapoltin. Ei ylimmääräisiä ilotulituksia :D tiiä sitten mikä oli.
se voi olla et niksanäpit teki tehtävänsä ::)